Endress+Hauser promag 30 - Page 60

Promag H Promag F
Nominal diameter DN 25...100 DN 25...2000
Nominal pressure
PN 16 DIN: PN 6 (DN 1200…2000)
PN 10 (DN 200...1000)
PN 16 (DN 65...150)
PN 40 (DN 25...50)
PN 16 /25 (DN 200...300),
Option
PN 40 (DN 65...100), Opt.
ANSI: Class 150 (1...24")
Class 300 (1...6"), Opt.
AWWA: Class D (28...48")
JIS: 10K (DN 50...300)
20K (DN 25...40)
20K (DN 50...300), Opt.
Process connection
Weld nipples for OD tube,
SMS, JIS, ISO and DIN 11850 tubes.
DIN 11851 thread. SMS thread.
ISO 2853 thread. Tri-Clamp.
ISO 2852.
Flange connection (DIN, ANSI, JIS)
Hygienic couplings acc. to DIN 11851
(DN 15...100)
Flange material 1.4435/316L DIN: St. 37.2,
stainless steel1.4571
ANSI: A105, 316L
AWWA: A105, A36
JIS: S20C, SUS 316L
Fluid temperature range,
liner material
–20 °C...+150 °C (PFA)
–20...+130 °C (with EPDM gaskets)
DN 15...600:
–40...+130 °C (PTFE)
DN 25...2000:
–20...+120 °C (Soft rubber)
DN 65...2000:
0...+80 °C (Hard rubber)
Ambient temperature
range
–20...+60 °C –20...+60 °C
Electrode material
1.4435 1.4435, Platinum/Rhodium 80/20,
Hastelloy C-22, Tantalum
Electrodes fitted Measuring and empty pipe
detection electrodes
DN 15...2000: Measuring, reference and
EPD electrodes (standard for 1.4435 and
Hastelloy C-22)
Min. conductivity
5 µS/cm 5 µS/cm
Gasket material
EPDM, Silicone —
Housing material 1.4301 DN 25...300: powder-coated die-cast
aluminium
DN 350...2000: varnished steel
Type of protection
IP 67
NEMA 4X
IP 67 (IP 68 option)
NEMA 4X (NEMA 6P as option)
CIP cleanable Yes (note max. temperature) Yes (note max. temperature)
SIP cleanable
Yes (note max. temperature) —
Power Supply The sensor is supplied by the measuring transmitter
Explosion protected
version
Ex Zone 2 VDE 0165
FM/CSA: Class I, Div. 2
CENELEC: EEx d/de;
Ex Zone 2 VDE 0165
FM/CSA: Class I, Div. 2
FM/CSA: Class I, Div. 1
SEV: EEx d/de
SEV: Ex n
others in preparation
Approvals EHEDG tested
3A approval
—
Cable entries
(Remote-mounted
version)
PG 13.5 cable glands (5...15 mm) or
NPT
1
/
2
", M20 x 1.5 (8...15 mm),
G
1
/
2
" threads for cable glands
PG 13.5 cable glands (5...15 mm) or
NPT
1
/
2
", M20 x 1.5 (8...15 mm),
G
1
/
2
" threads for cable glands
7. Technical Data Promag 30
60 Endress+Hauser