Enko CCS 3000 - User Manual

26 pages

Save Page as PDF

To Next Page

CCS 3000

Compressor Control System

User Manual

Main Page

Table of Contents2
CCS 3000 Introduction4
General4
2- System Introduction5
2-A Start-Up Screen5
2-B Main Operating Screen6
Stopped6
Stopping6
Starting7
Motor Driving7
Working on Unload7
Running on Load7
On Autowaiting7
Alarm and Warning Display / Indication8
Trip Alarm Display8
Warning Display9
Part Replacement & Maintenance Warning Display9
3-Ccs 3000 Menu Structure10
Alarm Menu (P1)10
Resetting Alarm10
Active Alarms Menu11
While in Alarm Menu, Press and Buttons Consecutively to Go to Alarm Records Menu. the Active Alarms Are Displayed in this Menu11
Alarm Records Menu11
Changing & Maintenance Time Menu (P2)11
Changing & Maintenance Remaining Times Screen12
Changing & Maintenance Remaining Time Reset12
Password Entry Screen12
Parameter Settings Screen13
User Parameters (P3)13
Operating Mode (P3.1)13
Pressure Unload (P3.2) (Bar/Psi)13
Wait on Unload (P3.3) (Seconds)14
Pressure Load (P3.4) (Bar/Psi)14
To Stop Delay (P3.5) (Seconds)14
Pressure Unit (P3.6)14
Temperature Unit (P3.7)14
To Start Delay (P3.8) (Seconds)14
Dryer Time (P3.9)14
User Password (P3.10)14
Service Parameters (P4)15
Pressure Parameters (P4.1)15
Stop Pressure (P4.1.1) (Bar/Psi)15
Temperature Parameters (P4.2) (Cel/Fah)15
Upper Temperature Limit (P4.2.1) (Cel/Fah)15
Temperature Alarm (P4.2.3) (Cel/Fah)16
Loading Temperature (P4.2.4) (Cel/Fah)16
Timing Parameters (P4.3)16
Star / Delta Duration (P4.3.1) (Sec)16
Delay for Start (P4.3.2) (Seconds)16
Auto Run Time (P4.3.4) (Seconds)16
Air Draining Time (P4.3.5) (Seconds)16
Max. Starts/Hour (P4.3.6)16
Indicated. this Parameter Can be Disabled by Setting It to "016
Service Hours (P4.4)16
Communication Parameters (P4.5)17
Load Valve Control Source (P4.5.1)17
Start/Stop Control Source (P4.5.2)17
Modbus Address (P4.5.4)18
Baud Rate (P4.5.5)18
Stop Bit (P4.5.6)18
Parity Bit (P4.5.7)18
Timeout Duration (P4.5.8)18
Calibration Parameters (P4.6)18
Pressure Offset (P4.6.1) (Bar/Psi)18
Temperature Offset (P4.6.2) (Cel/Fah)18
Screw Pressure Offset (P4.6.3) (Bar/Psi)18
Preheating Parameters (P4.7)19
Fan Settings (P4.8)19
Run Temperature (P4.8.1) (Cel/Fah)19
Stop Temperature (P4.8.2) (Cel/Fah)19
Minimum Work Time (P4.8.3) (Cel/Fah)19
Service Password (P4.9)19
Language Selection (P4.10)19
Factory Parameters (P5)19
Input Contact Type (P5.1)19
Functional Relay (P5.2)20
Pressure Sensor (P5.4)20
Clear Alarm List (P5.5)20
Return Factory Settings (P5.6)21
Boot Screen (P5.7)22
Factory Password (P5.8)22
CCS 3000 Version (P5.9)23
Bootloader Version (P5.10)23
Factory Calibration (P5.11)23
Temperature Sensor Type (P5.12)23
Screw Pressure Active (P5.13)23
Screw Pressure Value (P5.14)23
IN5 Function (P5.15)23
CCS3000 Mechanical Dimensions and Technical Specifications24
CCS3000 I/O List25
CCS3000 Connection Diagram26

Need help?

Do you have a question about the Enko CCS 3000 and is the answer not in the manual?

Enko CCS 3000 Specifications

General

Brand	Enko
Model	CCS 3000
Category	Control Systems
Language	English

Enko CCS 3000 - User Manual

Table of Contents

Enko CCS 3000 Specifications