Epson PP-100II - External Output Mode

45
Chapter 4 Development Guide for a Cooperative Application
4
OUT_STAC
KER
Specify an output
stacker.
[When the publisher is in Standard Mode]
[PP-100II / PP-100 / PP-100AP]
When selecting the stacker 2 as the
output stacker, specify "2".
When selecting the stacker 3 as the
output stacker, specify "3".
When selecting the stacker 4 as the
output stacker, specify "4".
[PP-100N]
When selecting the stacker 2 as the
output stacker, specify "2".
When selecting the stacker 4 as the
output stacker, specify "4".
[PP-50BD / PP-7050BD]
When selecting the stacker 2 as the
output stacker, specify "2".
When selecting the stacker 3 as the
output stacker, specify "3".
When not specified, the stacker specified in
the Environment Setting of TD Bridge is used.
If the Environment setting also has not
specified the output stacker, the stacker 2 will
be used.
[When the publisher is Not in Standard Mode]
Invalid (ignored if a stacker is specified)
One character PP-100II /
PP-100 /
PP-100AP
"2", "3", "4"
PP-100N
"2" or "4"
PP-50BD /
PP-7050BD
"2" or "3"
Arbitrary ● ●
DISC_TYPE Specify the type of
disc to be published.
[When the output device is PP-100 / PP-100N]
To publish a CD, specify "CD". To publish
a single-layer DVD, specify "DVD". To
publish a dual-layer DVD, specify "DVD-
DL".
[When the output device is PP-100II / PP-50BD
/ PP-7050BD (Non-Error Rate
Measurement Mode)]
To publish a CD, specify "CD". To publish
a single-layer DVD, specify "DVD". To
publish a dual-layer DVD, specify "DVD-
DL". To publish a single-layer BD, specify
"BD". To publish a dual-layer BD, specify
"BD-DL".
[When the output device is PP-100AP / PP-
7050BD(Error Rate Measurement Mode)]
Not specified. (Invalid if specified.)
Six characters Any of "CD",
"DVD", "DVD-DL"
Necessary ● --
WRITING_S
PEED
Specify the writing
speed depending on
the specified disc
type.
Specify the write speed [N] (_X write).
[CD-R]
Any of "40", "32", "24", "16", "10", "4".
[DVD-R]
Any of "12", "8", "6", "4", "2", "1".
[DVD+R]
Any of "12", "8", "6", "4", "2.4".
[DVD-R DL]
Any of "8", "6", "4", "2".
[DVD+R DL]
Any of "8", "6", "4", "2.4".
[BD]
PP-50BD / PP-7050BD
Any of "6", "4", "2".
PP-100II
Any of "8", "6", "4", "2".
[BD DL]
PP-50BD / PP-7050BD
Any of "6", "4", "2".
PP-100II
Any of "8", "6", "4", "2".
[Common to all disc types]
When a write speed other than listed
above is specified, the next slower speed
in the available settings is applied.
When not specified, the highest speed is
applied.
Three
characters
* Periods are
included.
Any of "40", "32",
"24", "16", "12",
"10", "8", "6", "4",
"2.4", "2", "1".
Arbitrary ● --
COMPARE Specify whether to
compare the written
data with the source
data.
Specify "YES" when carrying it out.
Specify "NO" when not carrying it out.
The data are not compared if "YES" is not
specified.
In the case of Audio CDs, the data are not
compared even if "YES" is specified.
Three
characters
"YES" or "NO" Arbitrary ● --
Key
name
Explanation How to specify the setting
Maximum
characters
Available
characters
(strings)
Necessary/
Arbitrary
Except PP-
100AP, Key
available
Yes/No
PP-100AP
Key
available
Yes/No