Epygi QX series Administrator's Guide

QX5
QXFXO4/QXISDN4/QXE1T1/QXFXS24; (SW Version 6.0.x) 48
QXFXO4/QXISDN4/QXE1T1/QXFXS24 Manual II: Administrator’s Guide
When Generate Progress Tone to PSTN/PBX checkbox is selected, QX generates ring tones to callers during ISDN call dialing. This feature is mainly
applicable to 2-stage dialing mode.
Enable CLIR Service checkbox selection enables Calling Line Identification Restriction (CLIR) service which displays the incoming caller ID only if
Presentation Indication is allowed on the remote side. Otherwise, if CLIR service is disabled, caller ID will be unconditionally displayed.
When the Alternative Disconnection Mode checkbox is not selected, QX will disconnect the call as soon as the disconnect message has been received
from the peer. When the checkbox is selected, QX’s user may hear a busy tone when peer has been disconnected.
P-Asserted-Identity:
The Disable P-Asserted-Identity radio button disables the P-Asserted-Identity feature for both incoming and outgoing calls.
The Override CLID with P-Asserted-Identity radio button selection enables SIP P-Asserted-Identity support. For the calls from SIP to ISDN if Invite SIP
message contains a P-Asserted-Identity, then the CallerID on ISDN is sent with the original Caller ID, which comes from the identity field. SIP user agent
should check for the existence of the P-Asserted-Identity, then the P-Preferred-Identity, then the Remote-Party-ID to fill the identity field.
For the calls from ISDN to SIP with restricted Caller ID, the SIP Invite message contains P-Asserted-Identity field with the value from the Caller ID on ISDN.
The SIP From field contains “anonymous”.
The Use Redirecting Number Info Element with P-Asserted-Identity radio button selection enables full support of the SIP P-Asserted-Identity.
For the calls from SIP to ISDN, if the SIP Invite message contains a P-Asserted-Identity or a P-Preferred-Identity or a Remote-Party-ID, then the CallerID on
ISDN contains the number from the user name field and the Redirecting Number IE contains the original number from the identity field. SIP user agent
should check for the existence of the P-Asserted-Identity, then the P-Preferred-Identity, then the Remote-Party-ID to fill the identity field.
For the calls from ISDN to SIP with Caller ID, the SIP Invite message contains P-Asserted-Identity field with the original number value from the Redirecting
Number IE on ISDN. The SIP From field contains the value from the user name.
When the Send Calling Party Subaddress checkbox is selected, QX will send the extension number as subaddress and the value defined in the Default
outgoing Caller ID field as caller ID on the outgoing call. When this checkbox is disabled, no subaddress information will be sent and the caller ID will be
defined according to the selection of the Use Default Outgoing Caller ID checkbox (see above). Caller ID information, along with the Subaddress, can be
displayed on the phone display depending on the phone and PBX settings and capabilities.
When the Ignore Empty Channel Identification in CALL PROCEEDING Msg. option is selected, QX will ignore the empty ISDN L3 Channel Identification
information element in CALL PROCEEDING message and will not response with STATUS message.
When this checkbox is disabled, QX will response with STATUS message on empty Channel Identification information element.
The B1 Channel and B2 Channel checkboxes enables/disables timeslots for voice transfer. Disabling the timeslot will prevent both incoming and
outgoing calls.
Clicking on the ISDN Stats link will open the ISDN Status page that displays ISDN traffic statistics on the corresponding ISDN trunk. The ISDN Stats link is
displayed for every active trunk on the board and refers to the page where ISDN trunk and traffic statistics can be viewed.

Epygi QX series Specifications

General

Brand	Epygi
Model	QX series
Category	PBX
Language	English