ESAB FABRICATOR 211i
SAFETY/INSTALLATION 3-2 Manual 0-5450
3.02 Specifications
Description Fabricator 211i Multi Process 3 in 1 Welder
Power Source Part No. W1004200
Power Source Dimensions H17.12" x W10.47" x D 24.29" (435mm x 266mm x D617mm)
Power Source Mass 57.3lb (26kg)
Cooling Fan Cooled
Welder Type Multi Process Welding System
Applicable Standard CSA E60974-1-00 / UL60974-1 / IEC 60974-1
Number of Phases Single Phase
Nominal Supply Voltage 208/230 VAC ± 10% 115VAC± 10%
Nominal Supply Frequency 50/60Hz 50/60HZ
Welding Current Range
MIG Mode
STICK Mode
TIG Mode
10-210 Amps
10-200 Amps
10-200 Amps
10-140 Amps
10-110 Amps
10-150 Amps
Wirefeed Speed Range 100 - 600 IPM 100 - 400 IPM
MIG Welding Voltage Range 14.5 - 24.5V DC 14.5 - 19V DC
Nominal OCV 70V DC
Effective Input Current (I1eff)
for MIG (GMAW/FCAW)
for STICK (SMAW)
for LIFT TIG (GTAW)
14.4A/11.2A
16.8A/15.8A
11.7A/11.5A
15.5A
17.8A
17.4A
Maximum Input Current (I1max)
for MIG (GMAW/FCAW)
for STICK (SMAW)
for LIFT TIG (GTAW)
32.2A/25.0A
33.6A/31.6A
23.3A/22.9A
24.5A
30.1A
29.4A
Single Phase Generator Requirement 7.5 KW *3.7 KW
MIG (GMAW/FCAW) Welding Output, 104°F, 10 min. 210A @ 20%,24.5V
122A @ 60%, 20.1V
95A @ 100%, 18.8V
110A @ 45%,19.5V
99A @ 60%, 19.0V
77A @ 100%, 17.9V
STICK (SMAW) Welding Output,1040°F, 10 min. 200A @ 25%,28.0V
130A @ 60%, 25.2V
101A @ 100%, 24.0V
110A @ 35%,24.4V
90A @ 60%, 23.6V
70A @ 100%, 22.8V
TIG (GTAW) Welding Output, 104°F, 10 min. 200A @ 25%,18.0V
130A @ 60%, 15.2V
101A @ 100%, 14.0V
150A @ 35%,16.0V
115A @ 60%, 14.6V
90A @ 100%, 13.6V
Open Circuit Voltage 70 V
Protection Class IP23S
Table 3-1: Fabricator 211i Specifications
Note 1: The Effective Input Current should be used for the determination of cable size & supply requirements.
Note 2: Motor start fuses or thermal circuit breakers are recommended for this application. Check local requirements for your
situation in this regard.
Note 3: Generator Requirements at the Maximum Output Duty Cycle.
* Some 115 VAC, 15 amp/20 amps electrical outlets fitted with GFCI (Ground Fault Circuit Interrupt) protection against nuisance
trip with this equipment due to worn or out of tolerance components in the GFCI. In such cases have the 115 VAC, 15 amp/20 amp
GFCI electrical outlet replaced by a qualified electrical trades person.
To Next Page
Loading...
Need help?
General
