To Next PageTo Next PageWhy does the head drift back when in operation on my Evh HARDEE LR50160?
If the Evh Lawn Mower head drifts back during operation, it could be due to an improper counter balance valve setting. Another cause may be cylinder leakage, which requires repair or replacement of the cylinders.
Why does my Evh HARDEE LR50160 pump whine?
If the Evh Lawn Mower pump whines, it could be due to a worn or damaged pump, which would require repair or replacement. Make sure the gate valve is open. Another possible cause is improper oil in the system, in which case you should replace the oil. Finally, the pressure setting on the relief valve might be too low.
Why does my Evh HARDEE LR50160 Lawn Mower motor whine?
If the Evh Lawn Mower motor whines, it may be due to a worn or damaged motor, requiring repair or replacement. Another potential cause is improper oil in the system, which can be resolved by replacing the oil. Additionally, the pressure setting on the relief valve might be too low.
What to do if my Evh HARDEE LR50160 Lawn Mower vibrates severely?
If your Evh Lawn Mower unit vibrates severely, it could be due to a broken blade, which requires replacing the blades, blade bolts, and nuts. Another cause could be mismatched or unbalanced blades. Also, check for a loose blade holder, repairing or replacing it as necessary. Finally, a loose output shaft may be the culprit, in which case you should repair or replace the shaft's bearings in the mower head housing.
Why do the blades loose speed in mowing with my Evh HARDEE LR50160 Lawn Mower?
If your Evh Lawn Mower blades lose speed while mowing, the issue could stem from an improper relief valve setting. In such cases, check the relief valve setting. Alternatively, there might be trash in the proportional valve, necessitating a check or replacement. Lastly, examine and replace the poppet valves in the motor if needed.
What to do if the filter gauge is in the red at all times on my Evh HARDEE LR50160 Lawn Mower?
If the Evh Lawn Mower filter gauge is always in the red, it could be due to a restricted filter, which would require repair or replacement. Another possibility is a bad gauge, also necessitating repair or replacement. Finally, the hydraulic oil might be too heavy for the region or climate, in which case you should replace the oil.
Why do the beams squeak when operating my Evh Lawn Mower?
If the Evh Lawn Mower experiences beams that squeak during operation, it could be due to a lack of lubrication or improper lubrication. Lube the hinge points. Another cause could be defective lube fittings, which would need to be repaired or replaced.
Why is there excessive slack in the boom hinges of my Evh HARDEE LR50160?
If the Evh Lawn Mower experiences excessive slack in the boom hinges, it's likely due to worn pins. Repair or replace the pins to resolve this issue.
Why does the boom drift down on my Evh HARDEE LR50160 Lawn Mower?
If the Evh Lawn Mower boom drifts down, it could be due to an improper counter balance valve setting. Another cause may be cylinder leakage, which requires repair or replacement of the cylinders.
Why won't the blades start up on my Evh HARDEE LR50160?
If your Evh Lawn Mower blades won't start up, it could be due to restricted oil flow, so open the gate valve. Another cause could be a problem with the blade off/on switch or electric circuit, so check for 12-volts at the coil. It may also be due to trash in the proportional valve.
General| Engine Type | 4-Stroke |
|---|---|
| Power Source | Petrol |
| Cutting Width | 51 cm |
| Cutting Height | 25-75 mm |
| Wheel Size | 8 inches |
Outlines essential safety rules for operating the mower, emphasizing operator responsibility.
Details the location, importance, and replacement of safety decals on the mower.
Explains the mower's self-contained hydraulic system and programmable processor.
Details the functions of the tethered grip's micro-joysticks and buttons for mower control.
Guides the user through getting started, attaching the mower, and initial operation.
Lists common problems with their possible causes and solutions for the hydraulic system.
