Extron electronics DTP CrossPoint 108 4K - Command and Response Table for Remote and Communications Protocol Commands; IPCP Pro 350 Information

DTP CrossPoint 4K Series Matrix Switchers • Programming Guide 71
Command and Response Table for Remote and Communications
Protocol Commands
Command Function
SIS Command
(Host to Unit)
Response
(Unit to Host)
Set administrator password
EX6)
CA
}
Ipa•
X6)]
Read administrator password
E
CA
} X6)]
Reset (clear) administrator password
E
•CA
}
Ipa•
]
Set user password
EX6)
CU
}
Ipu•
X6)]
Read user password
E
CU
} X6)]
Reset (clear) user password
E
•CU
}
Ipu•
]
Set parameters all at once
E
1*
X6#
CISG
}
Cisg1*
X6#
/
X6$
*
X6#]
Set IP address, subnet mask, and
gateway address to the default values
and reboot with this single command.
NOTE: Use the read available time zones command (
E
*TZON
}
) to determine and select the time zone variable (
X6!
) to enter for your
location with the set time zone command (
E
TZON
}
).
Read available time zones
E
*TZON
}
<multiple
X6!
*
X6@
s>
]
The DTP CrossPoint returns a list of
installed time zones.
Set time zone
EX6!
*TZON
}
Tzon
X6!
*
X6@]
Set serial port parameters
EX6%
*
X6^
,
X6&
,
X6*
,
X6(
CP
}
Cpn
X6%
•Ccp
X6^
,
X6&
,
X6*
,
X6(]
Read serial port parameters
EX6%
CP
}
X6^
,
X6&
,
X6*
,
X6(]
Configure flow control
EX6%
*
X7)
,
X7!
CF
}
Cpn
X6%
•Cfl
X7)
,
X7!]
Read flow control
EX6%
CF
} X7)
,
X7!]
Configure receive timeout
EX6%
*
X7@
,
X7#
CE
}
Cpn
X6%
•Cce
X7@
,
X7#
,
X7$
,
X7%]
NOTE: The configure command is sufficient as shown for most users, with the priority (
X7$
) and length or delimiter (
X7%
) omitted). The
response in this case is “
Cpn
X6%
•Cce
X7@
,
X7#
,0,00000L
]
,” with the default
X7$
and
X7%
values returned.
Read receive timeout
EX6%
CE
} X7@
,
X7#
,
X7$
,
X7%]
Set verbose mode
EX7^
CV
}
Vrb
X7^]
Read verbose mode
E
CV
} X7^]
Configure current port timeout
E
0*
X7&
TC
}
Pti0*
X7&]
Read current port timeout
E
0TC
} X7&]
Configure global IP port timeout
E
1*
X7&
TC
}
Pti1*
X7&]
Read global IP port timeout
E
1TC
} X7&]
NOTES:
• Duplicate port number assignments are not permitted (Telnet and Web port numbers cannot be the same) and result in E13.
• Remapping of ports other than to reset them to defaults (23 or 80) or disabling them (0) must be to port numbers greater than or
equal to
1024.
Set Telnet port map
E
<port #>MT
}
Pmt<port #>
]
Reset Telnet port map
E
23MT
}
Pmt00023
]
Disable Telnet port
E
0MT
}
Pmt00000
]
View Telnet port map
E
MT
}
<port #>
]
Set Web port map
E
<port #>MH
}
Pmh<port #>
]
Reset Web port
E
80MH
}
Pmt00080
]
Disable Web port
E
0MH
}
Pmh00000
]
View Web port map
E
MH
}
<port #>
]
IPCP Pro 350 Information
The DTP CrossPoint 108 4K IPCP models include a built-in IPCP Pro 350 control processor
that supports the LAN ports and other functionality. See the IPCP Pro Series User Guide at
www.extron.com.