DTP CrossPoint 4K Series Matrix Switchers • Programming Guide 56
General Matrix Switcher Commands
Symbol definitions
]
= Carriage return and line feed
}
= Carriage return (no line feed)
| = Pipe (can be used interchangeably with the
}
character)
• = Space
E = Escape key
W = Can be used interchangeably with the E character
X! = Input number 00
–
10
(
00
= untied input, valid for tie commands only)
X@ = Output number 00 – 08
(
00
= untied output, valid for tie commands only)
NOTE: 5a, 5b, 6a, and 6b are invalid X@ values.
X# = EDID value (resolution and rate) See EDID Values Table on page 59.
X$ = Output number (including duplicate, a and b, outs) 01, 02, 03, 04, 05a, 05b, 06a, 06b, 07, and 08
NOTE: 5 and 6 are invalid X$ values.
X% = EDID filename <name>.bin.
Can include a full path name. File carries 128 or 256 bytes of data.
X^ = Mute and auto memory status enable and disable 0 = Disable (unmute) 1 = Enable (mute) 2 = Mute video and sync
X& = Input audio source 0 = Auto (see Example 2 on page 60) (default)
1 = HDMI (digital audio)
2 = Analog 2-channel audio
X* = Output audio source 0 = Original HDMI audio 1 = Embed audio (from DSP) 2 = None
X( = Detected input audio format 0 = None 2 = 2-channel PCM
1 = Analog 3 = Bitstream
X1) = HDCP authorized device, freeze, and film 0 = Off or disable 1 = On or enable
X1! = HDCP output mode 0 = Auto (follow the input) (default)
1 = On (always encrypt HDMI outputs)
2 = Follow input with continuous DVI trials
3 = Always encrypt HDMI outputs with continuous DVI trials
X1@ = HDCP notification 0 = Black screen 1 = Green screen (default)
X1# = HDCP status (for inputs) 0 = No source device connected 2 = Connected source is not HDCP-compliant
1 = Connected source is HDCP-compliant
X1$ = HDCP status (for outputs) 0 = No monitor connected
1 = Monitor connected but does not support HDCP
2 = Monitor connected, supports HDCP, but the video signal is not encrypted
3 = Monitor connected, supports HDCP, and the video signal is encrypted
X1% = Video format 0 (input) = No signal detected
0 (output) = Auto (HDMI RGB Full to CEA sink or DVI to non-CEA sink)
1 = DVI (RGB 444, no audio, no InfoFrames)
2 = HDMI RGB Full (RGB 444, 000 - 255 audio, InfoFrames)
3 = HDMI RGB Limited (RGB 444, 016 - 255 audio, InfoFrames)
4 = HDMI YUV Full (RGB 444, 000 - 255 audio, InfoFrames)
5 = HDMI YUV Limited (RGB 444, 016 - 255 audio, InfoFrames)
6 = HDMI YUV Full (RGB 422, 000 - 255 audio, InfoFrames)
7 = HDMI YUV Limited (RGB 422, 016 - 255 audio, InfoFrames)
X1^ = Output video bit depth 0 = Auto (default) 1 = 8-bit
X1& = Video mute status 0 = No mutes 2 = Video and sync
1 = Video mute
X1* = Input signal status 0 = No signal detected 1 = Sync detected
X1( = TP and insertion input number 07 – 10
X2) = Switch position 0 = DTP 1 = HDBT (output only) 2 = XTP
X2! = TP (scaled) and insertion output number 05 – 08
To Next Page
