Extron electronics MAV Plus Series - Page 125

4-15
CrossPoint / MAV Matrix Switchers • Programmer’s Guide
Command/response table for SIS commands (continued)
Command ASCII command
(host to switcher)
Response
(switcher to host)
Additional
description
View ties, gain, volume, mutes, presets, and DSVP
N
X#
= Output number 01 – (maximum number of outputs for your model)
X@
= Input number (for tie) 00 – (maximum number of inputs for your model) (00 = untied)
X^
= Numeric dB value –18 to +24 (1 dB/step) (Default = 0 dB)
X*
= Volume adjustment range 0 – 64 (1 dB/step except for 0-to-1, which is 22 dB)
X1@
= Video/audio mute: 0 = no mutes
1 = video mute
2 = audio mute
3 = video and audio mute
X(
= Global or room preset # 00 - 32, 10 maximum for a room preset (00 = current configuration)
View RGBHV output tie
X#
&
X@]
Example:
15&
27
]
Input27RGBHVistiedto
output 15.
View video output tie
X#
%
X@]
Example:
7%
02
]
Input2videoistiedtooutput7.
View audio output tie
X#
$
X@]
Example:
3$
06
]
Input6audioistiedtooutput3.
View input gain or attenuation
X@
G
X^]
Example:
4G
-02
]
Gainforinput4is-2dB.
View output volume
X@
V
X*]
Example:
7V
55
]
Volume for output 7 is 55
steps (9 dB of attenuation,
86.5%oftotalvolume).
View output mutes
E
VM
}
X1@
1
X1@
2
...
X1@
n
]
Each
X1@
response is the
mute status of an output,
starting from output 1.
n=themaximumnumberof
outputs for this model.
Example:
CrossPoint 450 Plus 3232 HVA
E
VM
}
Mut00001000000230000000000000000000
]
Output 5 video, output 12
audio, and output 13 video
and audio are muted. All
other outputs are unmuted.
N
The “Mut” portion of the response appears only when the switcher is in Verbose mode 2 or 3. See the Verbose mode
command on page 4-23.
View video global preset
configuration
EX(
*
X#
*1VC
}
X@
n
•
X@
n+1
•...•
X@
n+
15
•Vid
]
Showpreset
X(
’s video
conguration.Show
the input (
X@
)tiedto16
sequential outputs, starting
from output
X#
.
Command description:
Response description:
preset#*startingoutput#(StO#)*1(=video)VC
input#(I#)tiedtoStO#•I#tiedtoStO#+1•I#tiedtoStO+2•...•I#tiedtoStO+15•Vid
]
N
The starting output number (
X#
) should always be “1” for matrix sizes of 16 outputs or smaller.
N
EX(
*
X#
*1VC
}
where
X(
= 0 returns the switcher’s current video configuration.
Example:
MAV Plus 3232
E
4*17*1VC
}
17Output:
Response = tied input:
input 24 tied to output 19
18 19 20 21 22 23 24 25 26 27 28
08•08•24•08•08•29•29•00•08•01•01•01•08•08•08•08•Vid
29 30 31 32
no tied input input 8 tied to output 29
Eachpositionshownintheresponseisanoutput:left=startingoutput(17),right=startingoutput+15(32).The
number in each position is the input tied to that output.
Inthisexample,preset4,videoinput1istiedtooutputs26through28;input8istiedtooutputs17,18,20,21,25,and
29through32;input24istiedtoouput19;andinput29istiedtooutputs22and23.Noinputistiedtooutput24.