Extron electronics MAV Plus Series - Page 126

Programmer’s Guide, cont’d
CrossPoint / MAV Matrix Switchers • Programmer’s Guide
4-16
Command/response table for SIS commands (continued)
Command ASCII command
(host to switcher)
Response
(switcher to host)
Additional
description
View ties, gain, volume, mutes, presets, and DSVP (continued)
N
X(
= Global or room preset # 00 - 32, 10 maximum for a room preset (00 = current configuration)
X#
= Output number 01 – (maximum number of outputs for your model)
X@
= Input number (for tie) 00 – (maximum number of inputs for your model) (00 = untied)
X1)
= Room # (for room presets) 10 max. (each can have up to 10 presets (
X(
s) assigned)
View audio global preset
configuration
EX(
*
X#
*2VC
}
X@
n
•
X@
n+1
•...•
X@
n+
15
•Aud
]
Showpreset
X(
’s audio
conguration.Show
the input (
X@
)tiedto16
sequential outputs, starting
from output
X#
.
Command description:
Response description:
preset#*startingoutput#(StO#)*2(=audio)VC
input#(I#)tiedtoStO#•I#tiedtoStO#+1•I#tiedtoStO#+2•...•I#tiedtoStO#+15•Aud
]
N
The starting output number (
X#
) should always be “1” for matrix sizes of 16 outputs or smaller.
N
EX(
*
X#
*2VC
}
where
X(
= 0 returns the switcher’s current audio configuration.
Example:
(MAV Plus 2412)
E
15*1*2VC
}
01Output:
Response = tied input:
input 1 tied to output 3
02 03 04 05 06 07 08 09 10 11 12
01•01•01•01•02•22•22•00•03•03•03•03•--•--•--•--•Aud
13 14 15 16
no tied input no outputs
Eachpositionshownintheresponseisanoutput:left=startingoutput(1),
right=startingoutput+15(16).Thenumberineachpositionistheinputtiedtothat
output.(Outputs13through16arenotpresentontheMAVPlus2412.)
Inthisexample,preset15,audioinput1istiedtooutputs1through4;input2istiedto
output5;input3istiedtooutputs9through12;andinput22istiedtooutputs6and7.
Noinputistiedtooutput8.Outputs13through16arenotpresentonthisswitcher.
View video room preset
configuration
EX1)
*
X(
*
X#
*1VC
}
X@
n
•
X@
n+1
•...•
X@
n+
15
•
Vid
]
Showroom
X1)
, preset
X(
’s
videoconguration.Show
the input (
X@
)tiedto16
sequential outputs assigned
to room
X1)
, starting from
output
X#
.
Command description:
Response description:
room#*roompreset#*startingoutput#(StO#)*1(=video)VC
input#(I#)tiedtoStO#•I#tiedtoStO#+1•...•I#tiedtoStO#+15•Vid
]
N
The starting output number (
X#
) should always be “1” for matrix sizes of 16 outputs or smaller.
View audio room preset
configuration
EX1)
*
X(
*
X#
*2VC
}
X@
n
•
X@
n+1
•...•
X@
n+
15
•
Aud
]
Showroom
X1)
, preset
X(
’s
audioconguration.Show
the input (
X@
)tiedto16
sequential outputs assigned
to room
X1)
, starting from
output
X#
.
Command description:
Response description:
room#*roompreset#*startingoutput#(StO#)*2(=audio)VC
input#(I#)tiedtoStO#•I#tiedtoStO#+1•...•I#tiedtoStO#+15•Aud
]
N
The starting output number (
X#
) should always be “1” for matrix sizes of 16 outputs or smaller.