7.
T
o
use radiocontrols with the same code, copy
the
ON - OFF
combination
to the other radiocontrols
without the need to change anything on the control
board
.
6.2
STORING SLH R
ADIOCONTROLS
It
is
possible to store a maximum
of
256 codes divided between
OPEN
A
and
OPEN
B/CLOSE.
1. On the
SLH
radiocontrol,
press
and hold down
P1
and
1.
P2
simultaneously.
2.
The
radiocontrol led
will
begin to flash.
3.
R
elease both push-buttons.
4.
Press
and hold down push-button
+
(SW3)
or
-
(SW2)
2.
and then
press
the
SETUP
push-button
(SW4),
to store
3.
total opening
(OPEN
A) or partial opening
(OPEN
B/
CLOSE)
respectively.
The
corresponding led
will
begin
to flash
slowly
for 5 secs.
4.
5.
R
elease both push-buttons.
6.
Within this
5 sec. period
while
the radiocontrol led
is
still
flashing, press
and hold down the required push-button
5.
on the radiocontrol (the radiocontrol led
will
come
on
with a fixed light).
7.
The
corresponding led will come on with a fixed light
6.3
STORING LC/RC
R
ADIOCONTROLS
(ONLY FOR SOME MARKETS)
It
is
possible to store a maximum of
256 codes divided between
OPEN
A
and
OPEN
B/CLOSE.
Use
the
LC/RC
remote
controls
only with
a
433 MHz receiving module.
Press
and hold down push-button
+
(SW3)
or
-
(SW2)
and then
press
the
SETUP
push-button
(SW4),
to store
total opening
(OPEN
A) or partial opening
(OPEN
B/
CLOSE)
respectively.
The
corresponding led
will
begin
to flash
slowly
for 5 secs.
R
elease the push-button.
Within
this 5 second period,
press
the required push-
button on the
LC/RC
remote control.
The led will come on with a fixed light for 1
second
,
indicating that the unit has been stored, and then
resume flashing for an additional 5 seconds during
which time another radiocontrol may be stored.
Once
the 5 seconds are up, the led
will
go off to indi-
cate that the procedure
is
complete
.
6.3.1
STORING LC/RC RADIOCONTROLS
REMOTELY
for 2 seconds and then go off to indicate the setting
has been stored.
8.
R
elease the radiocontrol push-button.
With LC/RC radiocontrols, other radiocontrols may
be
stored in remote mode,
i
.
e
. without operating directly
on
the board, using a
previously
stored radiocontrol.
9.
Press
the stored radiocontrol push-button twice
in
quick
1.
succession.
The automated system will carry out an
2.
opening control. Ensure the
automated
device
is
free of any obstacle by people
3.
or things.
T
o
enable other radiocontrols
with
the same
system
code,
4.
transfer
the system code of the stored radiocontrol push-
button to the corresponding push-button of the
radiocon-
trols
to be
added,
following the procedure
below:
5.
Obtain a radiocontrol already stored on one of its
2 channels
(OPEN
A or
OPEN B/CLOSE).
Press
and hold down push-buttons
P1
and
P2
simulta-
neously until both leds flash
slowly
for 5 secs.
Within
5 seconds, push the
previously
stored
radiocon-
trol push-button to activate the learning stage on
the
selected
channel
.
The
led on the board corresponding to the
channel
being stored flashes for 5 seconds, within which
time
the code of another radiocontrol must be sent.
The led will come on with a fixed light for 1
second
,
a. On the stored radiocontrol,
press
and hold
down
P1
and
P2
simultaneously.
b.
The
radiocontrol led
will
begin to flash.
c.
R
elease both push-buttons.
d.
Press
the stored push-button and hold down (the
radiocontrol led
will
come on with a fixed light).
e.
Bring
the radiocontrols closer to one another, press
and hold down the corresponding push-button
of
the radiocontrol to be
added,
releasing only
once
the led on the radiocontrol has issued a
double
flash to indicate that it has been stored.
indicating that the unit has been stored, and then
resume flashing for an additional 5 seconds during
which time other radiocontrols may be stored
and
then it
will
go
off
.
6.4
RADIOCONTROLS
DELETION
PROCEDURE
T
o
delete
ALL
the codes of the radiocontrols
entered
,
simply
press
down together the two push-buttons
+
(SW3)
and
-
(SW2),
then press the
SETUP
push-button
(SW4)
for
1 second, and hold the
first
two push-buttons pressed for
10 secs.
f.
Press
the stored radiocontrol push-button twice in
•
quick succession.
•
The automated system will carry out
an
opening control. Ensure the automated
•
device
is
free of any obstacle by
people
or things.
The 2 leds
RADIO1
and
RADIO2
will flash quickly for
10 secs.
The
2 leds
will
come on
with
a fixed light for 2 seconds
and then go off (deletion carried out).
R
elease both push-buttons.
This
operation
is
NOT reversible.
All
the codes
of the
radiocontrols
stored as
OPEN
A and
as
OPEN B/CLOSE will
be deleted.
To Next Page
Loading...
