EasyManua.ls Logo

Fisher 1000 - User Manual

Fisher 1000
28 pages
Save Page as PDF
Print Icon
To Next Page IconTo Next Page
To Next Page IconTo Next Page
Loading...
January 15, 2014
Lit. No. 94431, Rev. 07
CAUTION
Read this manual before installing or
operating the spreader.
Low‑Prole Tailgate Spreader
68810, 21927
Model 1000 & 2000
Owner's Manual
Original Instructions
This manual supersedes all editions with an earlier date.
This manual is for FISHER
®
Model 1000 & 2000 Low‑Prole Tailgate Spreaders
with serial numbers10003 and higher (Model 1000) and 20364 and higher (Model 2000).

Table of Contents

Questions and Answers

  • J
    Joshua SmithJul 26, 2025
    What to do if my Fisher Spreader does not operate but the indicator light is on?
    • A
      Ashley PrestonJul 26, 2025
      If your Fisher Spreader isn't working but the indicator light is on, there could be a few reasons. First, if you have a Variable Speed Control, the over-current protection might be activated due to an overloaded condition. Try turning the power off to reset the cab control, then press the START/BLAST switch to continue. Another possibility is damaged wiring or an open circuit between the cab control and the spreader. Inspect the plug connections at both the cab control and the spreader, and check the wire connections at the spreader motor and vehicle battery. If you find damaged wires or connectors, repair or replace them. Also, check the 30A in-line fuse and replace it if needed. Finally, if the spreader motor isn't running, and the shaft won't turn, you'll need to replace the motor.
  • D
    dianasmithJul 31, 2025
    Why does my Fisher Spreader spinner not turn even though the motor is running?
    • M
      Michael WalshJul 31, 2025
      If the motor of your Fisher Spreader is running but the spinner isn't turning, there are several things to check. First, make sure there isn't anything blocking the spinner's rotation and clear any obstructions. Next, examine the drive belt to see if it's loose or damaged; adjust the tension or replace the belt if needed. Also, verify that the motor pulley is securely attached to the motor shaft and tighten the set screw if it's loose, or replace the pulley if damaged. Check that the spinner pulley is properly attached to the spinner shaft; replace the cap screw and nut if they are missing or damaged, and replace the pulley if it's damaged. Lastly, the spinner shaft bearings may be dry or seized, so grease or replace the bearings.
  • P
    Patrick WrightAug 5, 2025
    How to troubleshoot no power to the cab control of my Fisher 1000?
    • T
      taylorcolemanAug 6, 2025
      If there's no power to the cab control of your Fisher Spreader and the indicator lights aren't on, start by checking the plug connection at the cab control to ensure it's secure. Then, inspect the battery lead in-line fuse and replace it (30 A) if it's blown, and look for any short circuits. Also, check the battery connection for any issues; make sure the battery isn't low, and clean or replace the ring terminal, coating it with dielectric grease. Examine the battery wiring harness for damage and repair or replace any damaged wires or the entire harness. If you have an older ON/OFF control, the control circuit breaker might be tripped; turn the control OFF, reset the circuit breaker, and then turn the control ON.
  • C
    campbelldianeAug 10, 2025
    What to do if ice control material is not flowing from my Fisher 1000 Spreader even when the spinner is turning?
    • C
      carrilloaliciaAug 10, 2025
      If the ice control material isn't flowing from your Fisher Spreader while the spinner is turning, it's likely due to bridging of the material or an obstruction in the hopper. To resolve this, unplug the spreader harness and tag it out if necessary. Then, inspect the hopper for any material that has bridged together or any obstructions, and clear them out.
  • R
    Richard NixonAug 15, 2025
    Why does the speed control dial not change the motor speed on my Fisher 1000?
    • K
      Kristin MartinezAug 16, 2025
      If the speed control dial on your Fisher Spreader's Variable Speed (PWM) cab control isn't changing the motor speed, the cab control may be malfunctioning, and you may need to replace it. Another potential cause is that the red and white connectors are incorrectly hooked up. Ensure they are correctly connected, matching red to red and white to white.
  • J
    James ZimmermanAug 20, 2025
    How to adjust the spread pattern on a Fisher Spreader?
    • O
      otaylorAug 20, 2025
      To adjust the spread pattern on your Fisher Spreader, unplug the spreader harness and tag it out, if required. Then, change the deflector adjustment to achieve the desired spread pattern.

Summary

PREFACE

SAFETY INFORMATION

SAFETY DEFINITIONS

Defines warning, caution, and note terms used in the manual.

WARNING;CAUTION LABELS

Illustrates and describes important safety labels on the spreader.

SERIAL NUMBER LABEL

Explains the format and meaning of the spreader's serial number.

SAFETY PRECAUTIONS

Lists essential safety precautions for operating and servicing the spreader.

PERSONAL SAFETY

Provides guidelines for personal safety during vehicle and spreader operation and maintenance.

FIRE AND EXPLOSION

Offers precautions regarding gasoline and fire hazards.

CELL PHONES

Advises against using cell phones while driving.

VENTILATION

Emphasizes the need for ventilation due to vehicle exhaust fumes.

BATTERY SAFETY

Details safety precautions when working with batteries.

NOISE

States the airborne noise emission level for the spreader operator.

VIBRATION

Provides vibration levels for hand-arm and whole body exposure.

TORQUE CHART

Lists recommended torque values for various fastener sizes.

LOADING

CERTIFICATION

Covers vehicle certification requirements for spreader installation.

APPROXIMATE MATERIAL WEIGHTS

Shows weight per cubic foot for common spreading materials.

MOUNTING THE SPREADER

RECEIVER MOUNT SPREADER

Instructions for mounting the spreader using a receiver hitch.

FIXED MOUNT SPREADER

Instructions for mounting the spreader directly to the truck bed.

SWING AWAY SPREADER

Steps for mounting the spreader with the Swing Away feature.

OPERATING THE SPREADER

DRIVING AND SPREADING ON SNOW AND ICE

Provides tips for safe driving and spreading in winter conditions.

CONTROLS

Describes the spreader's control options and their functions.

Adjusting the Spinner Speed

How to adjust the spreader's spinner speed using the control dial.

Blast;Maximum Speed

Instructions for using the blast or maximum speed function.

Diagnostic Indicator Light

Explains the diagnostic light and its error codes.

Variable Speed (PWM) Control - Old Style

Details the operation of the older PWM control interface.

Spinner Indicator Lights

Explains the meaning of the indicator lights on the control unit.

ON;OFF Control

Describes the ON/OFF control style for the spreader.

Starting and Stopping the Motor

Procedures for starting and stopping the spreader motor.

BLAST;Maximum Speed (New Style Only)

How to use the blast/max speed function on the new control style.

REMOVING THE SPREADER

SWING AWAY MOUNT

Steps to remove the spreader from a Swing Away mount.

RECEIVER MOUNT

Steps to remove the spreader from a receiver hitch mount.

FIXED MOUNT

Steps to remove the spreader from a fixed mount.

Removing the Brackets

Instructions for detaching mounting brackets from the vehicle.

Removing the Base Plates

Instructions for detaching base plates from the vehicle bumper.

MAINTENANCE

PRESEASON CHECK

Checklist for preparing the spreader before the ice control season.

AFTER EACH USE

Procedures for cleaning and lubricating the spreader after each use.

POSTSEASON MAINTENANCE

Steps for storing the spreader during the off-season to prolong its life.

DRIVE BELT REPLACEMENT

Detailed instructions for replacing the spreader's drive belt.

BEARING AND SET SCREW MAINTENANCE

Guidance on tightening set screws and greasing bearings.

FUSE REPLACEMENT

Information on replacing fuses in the spreader's electrical system.

RECYCLE

Guidelines for recycling the spreader at the end of its life.

4-PIN HARNESS WIRING DIAGRAM

2-PIN HARNESS WIRING DIAGRAM

TROUBLESHOOTING GUIDE

Fisher 1000 Specifications

General IconGeneral
BrandFisher
Model1000
CategorySpreader
LanguageEnglish

Related product manuals