FMC Technologies Smith Meter AccuLoad II Programming Workbook

Program Program
Code Function Code Description Entry Code
8 AB06030 Rev. 0.6 5/96
100
System General Purpose Directory
100
101 System Alarm Check/Reset Read only, Press E to clear None 101
Available Alarms
AC: Additive Communications** L5: Additive 5 Pulse**
A2: Print Cover Open L6: Additive 6 Pulse**
A4: Print Cover Open L7: Additive 7 Pulse**
B2: Buffer Overflow M1: Too Many Pulses Additive 1**
B4: Buffer Overflow M2: Too Many Pulses Additive 2**
CL: Clean Line M3: Too Many Pulses Additive 3**
CM: Communication M4: Too Many Pulses Additive 4**
DA: EEProm Bad M5: Too Many Pulses Additive 5**
DA: Ram Bad M6: Too Many Pulses Additive 6**
DA: Rom Uxx Bad M7: Too Many Pulses Additive 7**
DA: Watchdog Alarm N1: No Pulses Detected Address 1**
DA: Display Error N2: No Pulses Detected Address 2**
DA: Data Retention N3: No Pulses Detected Address 3**
DA: Display Boot Required N4: No Pulses Detected Address 4**
DA: Control Module N5: No Pulses Detected Address 5**
DA: Security Code N6: No Pulses Detected Address 6**
DA: Software Version N7: No Pulses Detected Address 7**
DA: Internal Temperature OA: Overrun
DA: Program Code O2: Printer Paper Out
DP: Down Pulse Error O4: Printer Paper Out
DR: Density Transducer PA: Power Fail*
D2: Printer Deselected PC: Pulse Collision
D4: Printer Deselected PR: Pressure Transducer
E2: Printer Error PS: Pulse Security
E4: Printer Error PT: Pulse Transmission
F1: Add 1 Feedback P2: Printer Communication
F2: Add 2 Feedback P4: Printer Communication
F3: Add 3 Feedback R1: Additive 1 Frequency**
F4: Add 4 Feedback R2: Additive 2 Frequency**
F5: Add 5 Feedback R3: Additive 3 Frequency**
F6: Add 6 Feedback R4: Additive 4 Frequency**
F7: Add 7 Feedback R5: Additive 5 Frequency**
H2: Printer Hardware R6: Additive 6 Frequency**
H4: Printer Hardware R7: Additive 7 Frequency**
IA: Injector Alarm** SF: Storage Full
I2: Printer Not Responding SP: Shared Printer
I4: Printer Not Responding TK: Ticket Alarm
K1: Low Additive 1** TP: Temperature Probe
K2: Low Additive 2** TT: Temperature Transducer
K3: Low Additive 3** U1: Unauthorize Command Failed Additive 1**
K4: Low Additive 4** U2: Unauthorize Command Failed Additive 2**
K5: Low Additive 5** U3: Unauthorize Command Failed Additive 3**
K6: Low Additive 6** U4: Unauthorize Command Failed Additive 4**
K7: Low Additive 7** U5: Unauthorize Command Failed Additive 5**
L1: Additive 1 Pulse** U6: Unauthorize Command Failed Additive 6**
L2: Additive 2 Pulse** U7: Unauthorize Command Failed Additive 7**
L3: Additive 3 Pulse** VF: Valve Fault
L4: Additive 4 Pulse** ZF: Zero Flow*
Note:
* These alarms apply to SEQ-11 and above firmware.
** These alarms apply to SEQ-13 and above firmware.

FMC Technologies Smith Meter AccuLoad II Specifications

General

Brand	FMC Technologies
Model	Smith Meter AccuLoad II
Category	Measuring Instruments
Language	English