What to do if pilot lights are not on and readouts are dark in Forma Scientific Accessories?
If the pilot lights are not on and the readouts are dark, verify the unit is plugged in and the main power switch is on. Also, check if the circuit breaker or the outlet overload protection has tripped. Ensure there is voltage at the outlet. A defective incubator wiring could also be the cause.
What to do if CO2 alarm and light are on in Forma Scientific Accessories?
If the CO2 alarm and light are activated, it could be because the CO2 level has deviated more than 1% from the setpoint, the CO2 supply has been interrupted, the CO2 inject circuit or solenoid is defective or the CO2 sensor fan is defective. If you reset the alarm and it activates again, investigate these potential causes.
What to do if CO2 display and FYRITE read 0% CO2 in Forma Scientific Accessories?
If the CO2 display and FYRITE both read 0% CO2, and the CO2 alarm is activated while the CO2 inject light is on, it could be due to a loss of CO2 supply, a defective CO2 solenoid, or a clogged CO2 in-line filter.
What to do if CO2 system indicator and readout are dark in Forma Scientific Accessories?
If the CO2 system indicator and readout are dark, and there is no control of CO2 in the chamber, first check if the circuit breaker has tripped. If not, the issue might be a defective switch, wiring, or CO2 module.
What to do if CO2 display shows some random number in Forma Scientific Accessories?
If the CO2 display shows a random number or decimal point, the readout board might be defective. Alternatively, there could be a defective output to the readout board from the CO2 control or faulty interconnecting wiring.
What to do if CO2 setpoint changes by itself in Forma Scientific Accessories?
If the CO2 setpoint changes by itself, it may be due to a faulty CO2 potentiometer or a defective CO2 control.
Why is actual CO2 higher than setpoint in Forma Scientific Accessories?
If the actual CO2 level is higher than the setpoint and readout, and re-zeroing only helps temporarily, the CO2 sensor might be defective, or the CO2 control might be incorrectly calibrated.
What to do if CO2 overshoots setpoint badly in Forma Scientific Accessories?
If the CO2 overshoots the setpoint badly, check if the CO2 sampler blower is inoperative. Also, a defective CO2 control, CO2 inlet pressure being too high, or the unit being in over temp could be the cause.
What to do if CO2 alarm sounded while CO2 level is controlling at setpoint in Forma Scientific Accessories?
If the CO2 alarm sounds even when the CO2 level is controlling at the setpoint, there might be excessive RFI or EMI near the unit, a faulty grounding circuit, or a defective CO2 control.
What to do if CO2 display will not go to zero in Forma Scientific Accessories?
If the CO2 display will not go to zero, ensure you are following the proper procedure: close the door and allow the temperature and RH to stabilize for eight hours. If the issue persists, the CO2 sensor or CO2 control may be defective.
Instructions for initial disinfection of interior surfaces before installation of components.
Steps for safely connecting the incubator to an appropriate electrical power supply.
Methods and instructions for filling the incubator's water jacket with distilled water.
Recommended methods for providing elevated humidity using the reservoir or pan.
How to set the desired operating temperature for the incubator chamber.
Procedure for setting the overtemperature safety limit to protect the unit.
Instructions for connecting the optional gas guard system for CO2 supply.
How to connect the CO2 gas supply directly without the gas guard.
Steps for accurately zeroing the CO2 controller using ambient air.
Procedure for setting the desired CO2 concentration percentage in the chamber.
General overview of the incubator's primary operational functions and features.
Procedures for thoroughly cleaning and disinfecting the incubator's interior surfaces.
Common symptoms and their possible causes for diagnosing incubator issues.
Detailed steps for calibrating the CO2 control module, including zero and span adjustments.
Instructions for safely removing and replacing the incubator's CO2 sensor.
General| Brand | Forma Scientific |
|---|---|
| Model | 3546 |
| Category | Accessories |
| Language | English |
To Next Page
