Frigidaire FAHE4044MW0 - Page 67

67
SECTION 6 - PUSH BUTTON SELECTION WASHER TECHNICAL DATA
Test
noitcerroC kcehC tseT
.)4( pets ot oG .seY ?lamron wolf retaw gnimocni eht sI .1 1 tseT
No. Go to step (2).
.)3( pets ot oG .seY ?no denrut stecuaf retaw gnimocni eht erA .2
No. Turn water faucets on.
3. Is the incoming water pressure above dekcolb ro deknik rof kcehC .seY ?isp02
incoming water hoses, clean the
incoming water screens. If problem still
remains, replace the water inlet valve
assembly.
No. Have customer correct inlet
pressure problem.
4. Does the fill water continue to enter the washer? Yes. Go to step (5).
No. Go to step (6).
5. Remove power from the washer. Did the water fill stop? Yes. Go to step (6).
No. Replace the water inlet valve
assembly. Pressure sensor checks
good. If yes, go to step (7). If no,
replace the pressure sensor.
og ,melborp eht tcerroc ton did siht fI .rosnes erusserp eht ecalpeR .6
to step (7).
og ,melborp eht tcerroc ton did siht fI .draob ecafretnI resU eht ecalpeR .7
to step (8).
.draob lortnoC niaM eht ecalpeR .8
Test 2 1. Is the washer leaking .kael retaw tcerroC .seY ?retaw
No. Go to step (2).
2. Is there an air leak in the air bell .melborp kael ria eht tcerroC .seY ?metsys
No. Go to step (3).
og ,melborp eht tcerroc ton did siht fI .rosnes erusserp eht ecalpeR .3
to step (4).
og ,melborp eht tcerroc ton did siht fI .draob ecafretnI resU eht ecalpeR .4
to step (5).
.draob lortnoC niaM eht ecalpeR .5
Test 3 1. Check the drain hose for rest .melborp tcerroC .noitcirtseR .snoitcir
No restriction. Remove the pump and
check for blockage. If blocked, remove
the restriction, if not, go to step (2).
2. Start the washer and check for 120 VAC at the drain pump. If 120 VAC present at the drain pump
when the pump is activated, then
replace the pump.
If Zero VAC. Check the wiring. If wiring
is good, replace the Main Control
board.
Test 4 1. Inspect the wiring between the pressure sensor and the main
control board.
Defective wiring. Correct wiring.
Good wiring. Then go to step (2).
og ,melborp eht tcerroc ton did siht fI .rosnes erusserp eht ecalpeR .2
to step (3).
og ,melborp eht tcerroc ton did siht fI .draob ecafretnI resU eht ecalpeR .3
to step (4).
.draob lortnoC niaM eht ecalpeR .4
.)2( pets ot oG .seY ?sehcni 5 evoba level retaw eht sI .1 5 tseT
No. Go to step (4).
2. Does water enter the washer co .)3( pets ot oG .seY ?ylsuounitn
No. Check air bell for clog. If no clog,
then go to step (4).
3. Remove power from the washer. Does the water stop coming in? Yes. Check wiring to valve assembly
for shorts. Wiring good, go to step (5).
No. Replace the water inlet valve
assembly.
4. Replace the pressure sensor. Did this correct the problem? Yes. Problem solved.
No. Go to step (5).
6 - 15