Function Settings
Function Settings
Extension Terminal Functions: E codes
Selects from the following functions by code.
0 : No function selection 2 : Aux. freq. setting 2
1 : Aux. freq. setting 1 3 : PID process command 1
--
0
Built-in Potentiometer
(Function selection)
Selects from the following functions by code.
0 : No function selection 3 : PID process command 1
1 : Aux. freq. setting 1 5 : PID feedback value
2 : Aux. freq. setting 2
0 : Keypad operation ( or key)
1 : Analog voltage input (terminal 12) (0 to +10V DC)
2 : Analog current input (terminal C1) (+4 to +20mA DC)
3 :
Analog voltage input (terminals 12) and analog current input (terminal C1)
4 : Potentiometer on the keypad
--
0
--
0
Analog Input Signal Definition for: [12]
[C1]
Selects from the following items by code.
0 : (1000) Multistep freq. selection (0 to 1 step)
1 : (1001) Multistep freq. selection (0 to 3 step)
2 : (1002) Multistep freq. selection (0 to 7 step)
4 : (1004) ACC/DEC time selection (2 steps)
6 : (1006) 3-wire operation stop command
7 : (1007) Coast-to-stop command
8 : (1008) Alarm reset
9 : (1009) Trip command (External fault)
10 : (1010) Jogging operation
11 : (1011) Freq. set 2 / Freq. set 1
19 : (1019) Write enable for keypad (Data changeable)
20 : (1020) PID control cancel
21 : (1021) Normal/Inverse mode changeover
24 : (1024) Link enable (RS-485 (standard), BUS (option))
33 : (1033) PID integration/differentiation reset
34 : (1034) PID integration hold
98 : Forward operation command
99 : Reverse operation command
*
The number in ( ) indicates logical inverse. (OFF when short-circuited)
--
98
--
99
Terminal Command Assignment to: [FWD]
[REV]
[SS1]
[SS2]
[SS4]
[RT1]
[HLD]
[BX]
[RST]
[THR]
[JOG]
[Hz2/Hz1]
[WE-KP]
[Hz/PID]
[IVS]
[LE]
[PID-RST]
[PID-HLD]
[FWD]
[REV]
0.00 to 100.00%
0.01 % 0.00
0.00 to 200.00%
0.01 % 100.0
0.00 to 5.00s
0.01 s 0.05
0.00 to 100.00%
0.01 % 100.0
Analog Input Adjustment
(Gain for terminal input [12])
(Gain)
(Filter)
(Gain reference point)
Analog Input Adjustment
(Gain for terminal input [C1])
(Gain)
(Filter)
(Gain reference point)
Bias(Frequency command 1)
(Bias reference point)
Bias (PID command 1) (Bias value)
(Bias reference point)
-100.00 to 100.00%
0.01 % 0.00
0.00 to 100.00%
0.01 % 0.00
0.00 to 200.00%
0.01 % 100.0
0.00 to 5.00s
0.01 s 0.05
0.00 to 100.00%
0.01 % 100.0
Motor Parameters: P codes
0.1 % 0.0
1
0.01 to 10.00 HP (when = 1)
0.01 to 10.00 kW (when = 0, 3, or 4)
0.00 to 99.99A
0.0 to 200.0%
0.01 HP
0.01 kW
0.01 A
Nominal applied
motor capacity
Rated current of Fuji's
standard motor
Motor Parameters
(Rated capacity)
(Rated current)
(Slip compensation gain)
0 : Standard motor (R123, R90)
1 : U.S.-made motor
3 : Standard motor (R88, R90)
4 : Others
--
Motor Selection
--
2
Control Functions of Frequency: C codes
Jump Frequency Band
0.0 to 30.0Hz 0.1 Hz 3.0
0.0 to 400.0Hz
0.1 Hz 0.0
0.0
0.0
Jump Frequency 1
2
3
Multi-step Frequency Settings 1
2
3
4
5
6
7
0.00 to 400.00Hz
0.01 Hz 0.00
0.00
0.00
0.00
0.00
0.00
0.00
0.00 to 400.00Hz
0.01 Hz 0.00
Jogging Frequency
0 : Inactive 1 : Active
--
0
Timer Operation
Frequency Command 2
Func.
code
Name Data setting range Factory settingMin. Unit
Func.
code
Name Data setting range Factory settingMin. Unit
Func.
code
Name Data setting range Factory settingMin. Unit
22
To Next Page
Loading...
