Fujitsu PRIMERGY RX600 S6 - Page 9

RX600 S6 Operating Manual
Contents
7.8 Added drive reported as defective . . . . . . . . . . . . . . 82
7.9 Error message on screen . . . . . . . . . . . . . . . . . . . 83
8 CSS components . . . . . . . . . . . . . . . . . . . . . . . . 85
8.1 Hot-plug components . . . . . . . . . . . . . . . . . . . . . 87
8.1.1 Hot-plug power supply units . . . . . . . . . . . . . . . . . . 87
8.1.1.1 Replacing a hot-plug power supply unit . . . . . . . . . . . 88
8.1.1.2 Adding a hot-plug power supply unit . . . . . . . . . . . . . 89
8.1.2 Hot-plug fans . . . . . . . . . . . . . . . . . . . . . . . . . . 91
8.1.2.1 Replacing a defective fan . . . . . . . . . . . . . . . . . . 92
8.1.2.2 Adding new fans . . . . . . . . . . . . . . . . . . . . . . . 93
8.1.3 Hot-plug HDD/SSD modules . . . . . . . . . . . . . . . . . . 94
8.1.3.1 HDD/SSD module and dummy module . . . . . . . . . . . 96
8.1.3.2 Removing/installing the dummy module . . . . . . . . . . . 97
8.1.3.3 Installing the HDD/SSD module . . . . . . . . . . . . . . . 98
8.1.3.4 Removing the HDD/SSD module . . . . . . . . . . . . . . 99
8.1.4 Hot-plug expansion cards . . . . . . . . . . . . . . . . . . . . 101
8.1.4.1 Identifying the defective CSS component . . . . . . . . . . 103
8.1.4.2 Removing a hot-plug expansion card . . . . . . . . . . . . 103
8.1.4.3 Removing a dummy module . . . . . . . . . . . . . . . . . 106
8.1.4.4 Installing a hot-plug expansion card . . . . . . . . . . . . . 107
8.1.5 Hot-plug memory boards . . . . . . . . . . . . . . . . . . . . 109
8.1.5.1 Identifying the defective memory . . . . . . . . . . . . . . . 110
8.1.5.2 Removing the memory board in question . . . . . . . . . . 111
8.1.5.3 Removing a defective memory module . . . . . . . . . . . 111
8.1.5.4 Installing a new memory module . . . . . . . . . . . . . . . 113
8.1.5.5 Reinstalling the memory board in question . . . . . . . . . 113
8.1.5.6 Adding a memory board . . . . . . . . . . . . . . . . . . . 114
8.2 Non-hot-plug components . . . . . . . . . . . . . . . . . . . 116
8.2.1 Identifying the defective CSS component . . . . . . . . . . . . 117
8.2.2 Replacing a non-hot-plug expansion card . . . . . . . . . . . . 117
8.2.2.1 Removing a non-hot-plug expansion card . . . . . . . . . . 117
8.2.2.2 Installing a non-hot-plug expansion card . . . . . . . . . . . 118
8.2.3 Replacing SFP+ transceiver modules . . . . . . . . . . . . . . 119
8.2.3.1 Removing an SFP+ transceiver module . . . . . . . . . . . 119
8.2.3.2 Installing SFP+ transceiver modules . . . . . . . . . . . . 121
8.3 Opening/Closing the server . . . . . . . . . . . . . . . . . . 125
8.3.1 Opening the server . . . . . . . . . . . . . . . . . . . . . . . 125
8.3.2 Closing the server . . . . . . . . . . . . . . . . . . . . . . . . 127