GE G30 - Page 695

GE Multilin G30 Generator Protection System vii
INDEX
PHASE CURRENT METERING......................................... 6-17
PHASE DIRECTIONAL OVERCURRENT
FlexLogic operands ..................................................... 5-132
logic............................................................................ 5-167
phase A polarization .................................................... 5-165
settings .............................................................5-165, 5-166
specifications ................................................................ 2-20
PHASE INSTANTANEOUS OVERCURRENT
see entry for PHASE IOC
PHASE IOC
FlexLogic™ operands .................................................. 5-133
logic............................................................................ 5-164
specifications ................................................................ 2-19
PHASE OVERVOLTAGE
FlexLogic operands ..................................................... 5-133
logic............................................................................ 5-196
Modbus registers........................................................... B-42
settings ....................................................................... 5-196
specifications ................................................................ 2-21
PHASE ROTATION ........................................................ 5-102
PHASE TIME OVERCURRENT
see entry for PHASE TOC
PHASE TOC
FlexLogic™ operands .................................................. 5-133
logic............................................................................ 5-163
settings ....................................................................... 5-162
specifications ................................................................ 2-19
PHASE UNDERVOLTAGE
FlexLogic operands ..................................................... 5-133
logic............................................................................ 5-195
Modbus registers........................................................... B-42
settings ....................................................................... 5-195
specifications ................................................................ 2-20
PHONE NUMBER FOR SUPPORT...................................... 1-2
PORT NUMBER LIST ....................................................... 5-29
POWER METERING
specifications ................................................................ 2-24
values ........................................................................... 6-19
POWER SUPPLY
description .................................................................... 3-12
low range ...................................................................... 2-26
removal to replace battery ............................................. 11-3
specifications ................................................................ 2-26
POWER SYSTEM
Modbus registers........................................................... B-33
PREFERENCES
Modbus registers........................................................... B-28
PROCESS BUS
overview ....................................................................... 3-15
PRODUCT INFORMATION ........................................ 6-28, B-9
PRODUCT SETUP .................................................... 5-8, 5-18
PRODUCTION TESTS ..................................................... 2-31
PROTECTION ELEMENTS ................................................. 5-4
PRP
actual values ................................................................. 6-12
explained ...................................................................... 5-31
settings ......................................................................... 5-29
specifications ................................................................ 2-28
PU QUANTITY ................................................................... 5-4
PUSHBUTTONS, USER-PROGRAMMABLE
see USER-PROGRAMMABLE PUSHBUTTONS
R
RADIUS server .........................................................5-16, G-1
REACTIVE POWER .................................................2-24, 6-19
REAL POWER......................................................... 2-24, 6-19
REAL TIME CLOCK
Modbus registers .......................................................... B-30
settings .........................................................................5-65
REAR TERMINAL ASSIGNMENTS ......................................3-7
RECLOSER CURVES .......................................... 5-124, 5-161
REDUNDANCY
PRP actual values..........................................................6-12
PRP explained ...............................................................5-31
settings .........................................................................5-29
specifications.................................................................2-28
RELAY ACTIVATION ........................................................4-27
RELAY ARCHITECTURE ................................................ 5-128
RELAY MAINTENANCE ......................................................7-3
RELAY NAME ..................................................................5-98
RELAY NOT PROGRAMMED ............................................1-18
REMOTE DEVICES
actual values ...................................................................6-6
device ID ..................................................................... 5-254
error messages................................................................7-9
FlexLogic operands...................................................... 5-136
Modbus registers ................................................. B-14, B-20
settings .......................................................................5-252
statistics ..........................................................................6-6
REMOTE DPS INPUTS
actual values ...................................................................6-5
settings .......................................................................5-255
REMOTE INPUTS
actual values ...................................................................6-4
FlexLogic operands...................................................... 5-136
Modbus registers ................................................. B-14, B-20
settings .......................................................................5-254
specifications.................................................................2-25
REMOTE OUTPUTS
DNA-1 bit pair..............................................................5-255
Modbus registers ................................................. B-66, B-67
UserSt-1 bit pair .......................................................... 5-256
REMOTE SETTING AUTHORIZATION ................................4-2
REPAIR ................................................................... 11-9, H-8
REPLACEMENT MODULES ..................................... 2-15, 2-16
REQUIREMENTS FOR INSTALLATION...............................1-5
RESET TO FACTORY DEFAULTS ......................................5-8
RESETTING..................................................5-8, 5-136, 5-256
to factory defaults ............................................................5-8
RESTRICTED GROUND FAULT
actual values .................................................................6-25
FlexLogic operands...................................................... 5-133
settings .......................................................................5-178
specifications.................................................................2-19
REVISION HISTORY ......................................................... H-1
RF IMMUNITY ..................................................................2-31
RFI, CONDUCTED ...........................................................2-31
RMS CURRENT ...............................................................2-24
RMS VOLTAGE ................................................................2-24
RS232
configuration....................................................................1-9
specifications.................................................................2-28
wiring ............................................................................3-29
RS422
configuration..................................................................3-40
timing ............................................................................3-41
two-channel application..................................................3-40
with fiber interface .........................................................3-42
RS485
description.....................................................................3-31
specifications.................................................................2-28