GE UR series

GE Multilin L60 Line Phase Comparison System v
INDEX
IMPORTANT CONCEPTS................................................... 1-4
IN SERVICE INDICATOR .......................................... 1-17, 7-3
INCOMPATIBLE HARDWARE ERROR................................ 7-4
INPUTS
AC current.............................................................2-15, 5-64
AC voltage ............................................................2-15, 5-65
contact inputs.................................. 2-15, 3-18, 5-251, 5-275
dcmA inputs ..........................................................2-15, 3-22
IRIG-B ..................................................................2-15, 3-27
remote inputs .................................2-15, 5-257, 5-258, 5-259
RTD inputs............................................................2-15, 3-22
virtual ......................................................................... 5-253
INSPECTION CHECKLIST ................................................. 1-1
INSTALLATION
communications ............................................................ 3-24
contact inputs/outputs...................................3-16, 3-18, 3-19
CT inputs ...................................................................... 3-12
RS485........................................................................... 3-25
settings......................................................................... 5-62
INSTANTANEOUS OVERCURRENT
see PHASE, GROUND, and NEUTRAL IOC entries
INTELLIGENT ELECTRONIC DEVICE ................................ 1-2
INTER-RELAY COMMUNICATIONS.................................. 2-18
INTRODUCTION................................................................ 1-2
INVERSE TIME UNDERVOLTAGE.................................. 5-194
IOC
see PHASE, GROUND, and NEUTRAL IOC entries
IP ADDRESS ................................................................... 5-16
IRIG-B
connection .................................................................... 3-27
error messages ............................................................... 7-5
settings......................................................................... 5-34
specifications ........................................................2-15, 2-17
ISO-9000 REGISTRATION ............................................... 2-21
K
KEYPAD..................................................................1-17, 4-23
L
LAMPTEST........................................................................ 7-2
LANGUAGE ..................................................................... 5-12
LASER MODULE ............................................................. 3-31
LATCHING OUTPUTS
application example...........................................5-255, 5-256
error messages ............................................................... 7-6
settings....................................................................... 5-254
specifications ................................................................ 2-16
LED INDICATORS ........................ 4-14, 4-15, 4-16, 4-22, 5-42
LED TEST
FlexLogic™ operand...................................................... 5-93
settings......................................................................... 5-40
specifications ................................................................ 2-13
LINE
pickup......................................................................... 5-125
LINE PICKUP
FlexLogic™ operands .................................................... 5-88
logic............................................................................ 5-126
Modbus registers...........................................................B-35
settings....................................................................... 5-125
specifications ................................................................ 2-10
LINK POWER BUDGET.................................................... 2-18
LOAD ENCROACHMENT
FlexLogic™ operands.....................................................5-88
Modbus registers .......................................................... B-32
settings ............................................................ 5-153, 5-154
specifications.................................................................2-13
LOGIC GATES .................................................................5-94
LOST PASSWORD ....................................................5-9, 5-10
LV FAULT ..........................................................................9-4
M
MAINTENANCE COMMANDS .............................................7-2
MANUFACTURING DATE .................................................6-22
MEMORY MAP DATA FORMATS ..................................... B-64
MEMORY VOLTAGE LOGIC ...........................................5-128
MENU HEIRARCHY................................................. 1-17, 4-25
MENU NAVIGATION....................................... 1-17, 4-24, 4-25
METERING
conventions .......................................................... 6-10, 6-11
current...........................................................................2-14
frequency ......................................................................2-15
power ............................................................................2-14
voltage ..........................................................................2-14
METERING CONVENTIONS .............................................6-11
MHO DISTANCE CHARACTERISTIC ..............................5-130
MODBUS
data logger .............................................................. B-6, B-7
event recorder ................................................................ B-7
exception responses ....................................................... B-5
execute operation ........................................................... B-4
fault report...................................................................... B-7
flex state parameters .....................................................5-52
function code 03/04h....................................................... B-3
function code 05h ........................................................... B-4
function code 06h ........................................................... B-4
function code 10h ........................................................... B-5
introduction .................................................................... B-1
memory map data formats ............................................. B-64
obtaining files ................................................................. B-6
oscillography .................................................................. B-6
passwords ...................................................................... B-8
read/write settings/actual values...................................... B-3
settings ................................................................ 5-16, 5-33
store multiple settings ..................................................... B-5
store single setting.......................................................... B-4
supported function codes ................................................ B-3
user map .....................................................5-33, B-11, B-23
MODEL INFORMATION ....................................................6-22
MODIFICATION FILE NUMBER ........................................6-22
MODULE FAILURE ERROR................................................7-4
MODULES
communications.............................................................3-24
contact inputs/outputs .................................. 3-16, 3-18, 3-19
CT.................................................................................3-13
CT/VT.....................................................................3-12, 5-7
direct inputs/outputs.......................................................3-31
insertion ...................................................................3-6, 3-7
order codes .....................................................................2-6
power supply .................................................................3-11
transducer I/O................................................................3-22
VT.................................................................................3-13
withdrawal ................................................................3-6, 3-7
MONITORING ELEMENTS..............................................5-224
MOUNTING.................................................................3-1, 3-2