TABLE OF CONTENTS
SAFETY RULES . . . . . . . . . . . . . . . . . . . . . . .5
ELECTRICAL REQUIREMENTS . . . . . . . . . . . . . .6
Grounding instructions . . . . . . . . . . . . . . . . . . . . . . .6
Circuit capacity . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6
Converting the motor to 220V . . . . . . . . . . . . . . . . .6
Extension cords . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6
IDENTIFICATION OF MAIN PARTS AND
COMPONENTS . . . . . . . . . . . . . . . . . . . . . . .
7
UNPACKING & SET UP . . . . . . . . . . . . . . . . . .8
Unpacking . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .8
List of contents . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .8
Additional requirements for set up . . . . . . . . . . . . .8
PLACEMENT WITHIN THE SHOP / ESTABLISHING A
SAFETY ZONE . . . . . . . . . . . . . . . . . . . . . . . .
9
CLEAN UP . . . . . . . . . . . . . . . . . . . . . . . . . .9
ASSEMBLY INSTRUCTIONS . . . . . . . . . . . . . .10
Assemble the folding stand (#50-095) . . . . . . . . .10
Assemble the fixed leg stand (#50-096) . . . . . . . .11
Assemble the saw . . . . . . . . . . . . . . . . . . . . . . . . . .12
Assemble the front fence rails . . . . . . . . . . . . . . . .13
Assemble the rear fence rails . . . . . . . . . . . . . . . .14
Mount the switch . . . . . . . . . . . . . . . . . . . . . . . . . . .14
Install / remove a saw blade . . . . . . . . . . . . .15
Adjusting the bevel angle pointer . . . . . . . . .15
Selecting, install and adjusting riving knife . . .15
Select a riving knife . . . . . . . . . . . . . . . . . . . . . . . . .15
Removal/installation . . . . . . . . . . . . . . . . . . . . . . . .16
Centering the splitter/riving knife on the blade .16
Remove/install the blade cover . . . . . . . . . . .16
Remove . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .16
Install . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .17
Remove/install the anti-kickback pawls . . . . .17
Level the table insert . . . . . . . . . . . . . . . . . .17
Align and level the rip fence . . . . . . . . . . . . .18
Align the rip fence parallel to the blade . . . . . . .18
Align the rip fence 90º to the table . . . . . . . . . . . .18
Level the fence . . . . . . . . . . . . . . . . . . . . . . . . . . . . .18
Adjust & align rip fence pointer . . . . . . . . . . .19
Connecting to a dust collector . . . . . . . . . . .19
BASIC ADJUSTMENTS AND CONTROLS . . . . . .19
Connecting to a power source . . . . . . . . . . . . . . .19
ON / OFF switch and safety pin . . . . . . . . . . . . . . .20
OPERATING INSTRUCTIONS . . . . . . . . . . . . .20
Ripping . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .20
Bevel ripping . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .21
Ripping small work pieces . . . . . . . . . . . . . . . . . . .21
Cross cutting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .21
Align-a-cut . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .21
Bevel cross cutting . . . . . . . . . . . . . . . . . . . . . . . . . .22
Adjusting and using the miter gauge . . . . . . .22
Adding an auxiliary fence to the miter gauge . .22
Miter cuts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .23
Compound mitering . . . . . . . . . . . . . . . . . . . . . . . .23
Using a dado head blade . . . . . . . . . . . . . . .23
Instructions for foldin & unfolding the stand
(#50-095)
. . . . . . . . . . . . . . . . . . . . . . . . .24
RECOMMENDED OPTIONAL ACCESSORIES . . . .24
PARTS LIST AND DIAGRAMS . . . . . . . . . .25 - 35
To Next Page
Loading...
