What to do if Gfp Laminator rollers do not turn after pressing 'Run'?
If the rollers on your Gfp Laminator do not turn after pressing the 'Run' button: 1. Check if the emergency switch is engaged and disengage it. 2. The roller nip pressure might be too high; reduce the nip pressure of the rubber rollers.
How to fix curled lamination output from Gfp Laminator?
Curled lamination output from your Gfp Laminator can be corrected by: 1. If the sheet is curled upward, reduce the top roll tension. 2. If the sheet is curled downward, reduce the bottom roll tension.
How to remove wrinkles in film from Gfp Laminator?
Wrinkles appearing in the film on both top and bottom during lamination with your Gfp Laminator are likely caused by too much nip roller pressure. Reduce the nip pressure using the hand wheel.
Why is the heat roller not heating up in my Gfp 563TH?
If the heat roller in your Gfp Laminator is not heating, the heater might not be set. Switch the heater on and adjust the temperature setting knob.
What causes the film supply roll to get loose on Gfp 563TH Laminator?
If the film supply roll on your Gfp Laminator gets loose during operation, there might not be enough brake tension on the supply roll. Increase the brake tension on the supply roll.
Why does the backing paper get loose on Gfp Laminator?
If the backing paper gets loose when being rolled up on your Gfp Laminator, it indicates that there is not enough brake tension on the backing paper rewind roller. Increase the brake tension on the backing paper rewind roller.
Provides a welcome message and instructions to read the manual.
Outlines critical safety warnings for machine operation and maintenance.
Only authorized technicians should perform repairs on the laminator.
Read all instructions before connecting power or operating the machine.
Essential safety precautions must be followed during installation and use.
Report shipping damage promptly and avoid extreme environmental locations.
Ensure accessible, grounded outlets and verify voltage compatibility.
Do not use damaged wires/sockets; use licensed electricians for wiring.
Never defeat or remove safety equipment like interlocks, shields, or guards.
Keep body parts and clothing away from rollers to prevent entanglement.
Use machine only for intended purposes; keep out of reach of children.
Avoid unattended operation, flammable materials, and hot rollers.
Disconnect power for maintenance; lift top roller when idle.
Place on level surface; maintain 8x10 ft space and clean environment.
Avoid cutting films on rollers; contact distributor for repairs.
Operator must be present; avoid direct sun, dust, and vibrations.
Identifies indicators for cold/hot modes and readiness, plus temperature display.
Explains switches for temperature, direction, and operation modes.
Machine lacks continuous reverse; photo-eye reset procedure noted.
Steps to reset machine operation if the photo-electric eye stops it.
Instructions for safely removing the machine from its shipping crate.
Steps to remove the heat tube package secured within the crate.
Procedures for lifting and removing the machine from the shipping skid.
Steps for assembling the machine's support stand.
Instructions for placing the machine onto its assembled stand.
Warning to handle the machine with care during lifting and placement.
Details on how to secure the machine to the stand using anchor bolts.
Step-by-step guide for installing the heat tube into the roller assembly.
Detailed steps for properly inserting the heat tube component.
Instructions for connecting the electrical wiring for the heat tube.
Guidance on installing the take-up reel assembly.
Adjust rewind tube pressure for proper backing paper removal and film feeding.
Final checks and connections required after initial setup.
Plug in foot pedal, check drive chains, set screws, and electrical connections.
Procedures for safely removing the press roller assembly.
Unscrew thumb screw and lift off the press roller assembly.
Step-by-step guide for loading film rolls onto the supply shaft.
Loosen/reattach adaptor, position film, fasten screws, adjust brake tension.
Step-by-step guide for threading film through the laminator rollers.
Load film, lift roller, thread through, separate liner, tack adhesive.
Ensure film is wrinkle-free; use cutter carefully to avoid heat roller damage.
Instructions for powering on and operating the laminator.
Plug in, turn on power, select cold or hot mode, and set temperature.
Match roller temp to material; LCD shows actual temp (inactive in cold mode).
Adjusting the gap between the laminator rollers for proper pressure.
Use hand-wheel to adjust roller pressure; clockwise lowers, counter-clockwise raises.
Avoid excessive pressure; 55" model requires less nip pressure.
Procedure to check the uniformity of the roller gap across the laminator.
Steps to address and fix uneven roller gaps by adjusting components.
Information on installing and operating the optional rewind device.
Steps for installing the rewind device and operating its motor functions.
To Next Page
General
