GLP impression X5 - Page 74

www.glp.de CONTROL / SETTINGS
74 impresssion X5 User Manual
White Point: 8000K (3 sec.)
138
139
54.1
54.5
White Point: 6500K (3 sec.)
140
141
54.9
55.3
White Point: 5600K (3 sec.)
142
143
55.7
56.1
White Point: 4200K (3 sec.)
144
145
56.5
56.9
White Point: 3200K (3 sec.)
146
147
57.3
57.6
No function
148
149
58.0
58.4
Sub Module mode Normal (3 sec.)
150
151
58.8
59.2
Sub Module mode Independent (3 sec.)
152
153
59.6
60.0
No function
154
165
60.4
64.7
Color Mode: RGB [1] (3 sec.)
166
167
65.1
65.5
Color Mode: RGBL [2] (3 sec.)
168
169
65.9
66.3
Color Mode: x;y [3] (3 sec.)
170
171
66.7
67.1
No function
172
181
67.5
71.0
iQ. Gamut: FULL (3 sec.)
182
183
71.4
71.8
iQ. Gamut: Rec. 2020 (3 sec.)
184
185
72.2
72.5
iQ. Gamut: Rec. 706 (3 sec.)
186
187
72.9
73.3
No function
188
191
73.7
74.9
Hibernation Off (3 sec., fixture will reset)
192
192
75.3
75.3
Hibernation On (3 sec.)
193
193
75.7
75.7
No function
194
195
76.1
76.5
Pan range: Normal (3 sec.)
196
197
76.9
77.3
Pan range : Extended (3 sec.)
198
199
77.6
78.0
No function
200
201
78.4
78.8
Accessory: None
202
203
79.2
79.6
Accessory: Egg crate
204
205
80.0
80.4
Accessory: Snoot
206
207
80.8
81.2
No function
208
215
81.6
84.3
PWM Optimal (3 sec.)
216
217
84.7
85.1
PWM High 1 (3 sec.)
218
219
85.5
85.9
PWM High 2 (3 sec.)
220
221
86.3
86.7
PWM Max. (3 sec.)
222
223
87.1
87.5
No function
224
229
87.8
89.8
Save as User Settings Preset 1 (3 sec.)
230
231
90.2
90.6
Save as User Settings Preset 2 (3 sec.)
232
233
91.0
91.4
Save as User Settings Preset 3 (3 sec.)
234
235
91.8
92.2
No function
236
237
92.5
92.9
Load User Settings Preset 1 (3 sec.)
238
239
93.3
93.7
Load User Settings Preset 2 (3 sec.)
240
241
94.1
94.5
Load User Settings Preset 3 (3 sec.)
242
243
94.9
95.3
Load Settings Default
244
245
95.7
96.1
No function
246
249
96.5
97.6
Reset pan/tilt (3 sec.)
250
251
98.0
98.4
Reset head (3 sec.)
252
253
98.8
99.2
Reset ALL (3 sec.)
254
255
99.6
100
To reduce the risk of accidentally changing settings, the commands on the Control /
Settings channel must be held for a certain time before they are executed. The above
table indicates the number of seconds that you must hold a command.