GRAPHTEC FC7000MK2-130 - 7. ADJUSTMENTS

FC7000-UM-251-9370 1-2
1. INTRODUCTION
FC7000MK2-60 FC7000MK2-75 FC7000MK2-100 FC7000MK2-130 FC7000MK2-160
CPU 32-bit
Configuration Grit-rolling plotter
Drive Digital servo
Max. cutting area
(expanded mode)
50m x 610 mm 50m x 762 mm 50m x 1067
mm
50m x 1372
mm
50m x 1626
mm
Guaranteed precision cutting area
*1
15m x 590 mm 15m x 742 mm 15m x 1047
mm
15m x 1352
mm
15m x 1606
mm
Mountable media width Max. 866 mm,
Min. 50 mm
Max. 920 mm,
Min. 50 mm
Max. 1224 mm,
Min. 50 mm
Max. 1529 mm,
Min. 50 mm
Max. 1834 mm,
Min. 50 mm
Max. cutting speed (Axial) 148.5cm/sec (45 ips)
Specifiable speeds 1, 2, 3, 4, 5, 6, 7, 8, 9, 10, 15, 20, 25, 30, 35, 40, 45, 50, 55, 60, 70, 80, 90, 100, 105 cm/sec
Cutting pressure 48 steps, 0.196-5.88N (20-600gf)
Min. character size 3mm (0.125 in.) alphanumeric Helvetica med. Font
Mechanical resolution 0.005mm
Programmable resolution GP-GL: 0.01/0.05/0.025/0.01mm, HP-GL: 0.025mm
*2
Repeatable accuracy
*1
Max. 0.1 mm/2-m unit (excluding media shrinkage)
Number of cutters/pens 1 (2 for the optional 2-pen models)
*3
Pen types Water-based fiber-tip, oil-based ballpoint and disposable ink pens
Pouncing tool type Pouncing tool: PPA33-TP12, 1.2-mm pin diameter)
*4
Compatible media Mono-vinyl chloride media, fluorescent media, and media for illuminated displays,
high reflective media, up to 0.25mm thick, Sandblast rubber up to 1mm thick
*5
Compatible paper for pouncing Regular paper from 0.06 to 0.13 mm thick
Standard interfaces RS-232C/USB (Auto switching)
Buffer memory 2 MB
Resident command sets GP-GL/HP-GL(Control panel switching)
LCD Panel 20x4 - Supports 7 languages: with amber backlight
Power supply 100-240VAC/50-60 Hz (Auto switching)
Power consumption 160VA max.
Operating environment Temperature: +10˚C to +35˚C
Humidity: 35% to 75% (non-condensing)
Guaranteed accuracy environment Temperature: +16 ˚C to +32 ˚C
Humidity: 35% to 70%(non-condensing)
External dimensions without stand 1110 x 402 x
477mm
1260 x 402 x
477mm
1560 x1210 x
715mm
1860 x 1210 x
715mm
2120 x 1210 x
715mm
Weight 22 kg 29 kg 43 kg
(including stand)
51 kg
(including stand)
59 kg
(including stand)
*1 When the optional basket and Graphtec-specified media are used.
*2 HP-GL is a registered trademark of Hewlett-Packard Company.
*3 The 2-pen unit is a factory-installed option. It cannot be retrofitted.
*4 The PPA32-TP12 pouncing pen cannot be used.
*5 The CB15UA cutter blade and a reinforced backing sheet must be used when cutting high-intensity reflective film.