Greenlee 555 - Special Bending Information Chart (Continued); Rigid;IMC Conduit Bending Data

Greenlee Textron / Subsidiary of Textron Inc.
22
4455 Boeing Dr., Rockford, IL 61109-2988 815/397-7070
555 Electric Bender
1/2 RIGID/IMC Dia. = 0.84 Radius = 4.5 X = 3.34
Y 15 2.17 9.90 17.63 25.35 33.08 40.81 52.40 63.99 87.17 133.54
L1 15 7.72 15.45 23.18 30.90 38.63 46.36 57.95 69.54 92.72 139.09
L2 15 8.90 16.63 24.35 32.08 39.81 47.54 59.13 70.72 93.90 140.26
Z 15 11.99 19.45 26.92 34.38 41.85 49.31 60.51 71.70 94.09 138.88
MINIMUM H = 1.17
Y 22.5 5.12 10.35 15.57 20.80 26.02 33.86 41.70 57.38 88.74
L1 22.5 5.20 10.43 15.66 20.88 26.11 31.33 39.17 47.01 62.69 94.05
L2 22.5 6.97 12.20 17.42 22.65 27.88 33.10 40.94 48.78 64.46 95.82
Z 22.5 9.96 14.79 19.62 24.44 29.27 34.10 41.34 48.59 63.07 92.04
MINIMUM H = 1.96
Y 30 2.61 6.61 10.61 14.61 18.61 24.61 30.61 42.61 66.61
L1 30 7.94 11.94 15.94 19.94 23.94 29.94 35.94 47.94 71.94
L2 30 10.30 14.30 18.30 22.30 26.30 32.30 38.30 50.30 74.30
Z 30 12.68 16.14 19.61 23.07 26.54 31.73 36.93 47.32 68.11
MINIMUM H = 2.88
Y 45 2.69 5.52 8.34 11.17 15.42 19.66 28.14 45.11
L1 45 8.29 11.12 13.95 16.78 21.02 25.26 33.75 50.72
L2 45 11.83 14.65 17.48 20.31 24.55 28.80 37.28 54.25
Z 45 13.07 15.07 17.07 19.07 22.07 25.07 31.07 43.07
MINIMUM H = 5.00
Y 60 0.51 2.81 5.12 7.43 10.90 14.36 21.29 35.15
L1 60 8.75 11.06 13.37 16.84 20.30 27.23 41.09
L2 60 13.47 15.78 18.09 21.55 25.01 31.94 45.80
Z 60 13.15 14.31 15.46 17.20 18.93 22.39 29.32
MINIMUM H = 7.39
Y 90 1.74 3.74 6.74 9.74 15.74 27.74
L1 90 13.07 16.07 22.07 34.07
L2 90 20.14 23.14 29.14 41.14
Z 90 12.34 12.34 12.34 12.34
MINIMUM H = 12.34
3/4 RIGID/IMC Dia. = 1.05 Radius = 4.64 X = 3.34
Y 15 1.75 9.48 17.20 24.93 32.66 40.39 51.98 63.57 86.75 133.11
L1 15 7.72 15.45 23.18 30.90 38.63 46.36 57.95 69.54 92.72 139.09
L2 15 8.94 16.66 24.39 32.12 39.84 47.57 59.16 70.75 93.94 140.30
Z 15 12.03 19.49 26.95 34.42 41.88 49.35 60.54 71.74 94.13 138.92
MINIMUM H = 1.18
Y 22.5 4.82 10.04 15.27 20.50 25.72 33.56 41.40 57.08 88.44
L1 22.5 5.20 10.43 15.65 20.88 26.11 31.33 39.17 47.01 62.69 94.05
L2 22.5 7.02 12.25 17.48 22.70 27.93 33.16 41.00 48.83 64.51 95.87
Z 22.5 10.01 14.84 19.67 24.50 29.33 34.16 41.40 48.64 63.13 92.10
MINIMUM H = 1.98
Y 30 2.37 6.37 10.37 14.37 18.37 24.37 30.37 42.37 66.37
L1 30 7.94 11.94 15.94 19.94 23.94 29.94 35.94 47.94 71.94
L2 30 10.37 14.37 18.37 22.37 26.37 32.37 38.37 50.37 74.37
Z 30 12.75 16.22 19.68 23.15 26.61 31.81 37.00 47.40 68.18
MINIMUM H = 2.91
Y 45 2.48 5.31 8.14 10.97 15.21 19.45 27.94 44.91
L1 45 8.29 11.11 13.94 16.77 21.01 25.26 33.74 50.71
L2 45 11.93 14.76 17.59 20.42 24.66 28.90 37.39 54.36
Z 45 13.18 15.18 17.18 19.18 22.18 25.18 31.18 43.18
MINIMUM H = 5.08
Y 60 0.30 2.61 4.92 7.23 10.70 14.16 21.09 34.94
L1 60 8.74 11.05 13.36 16.82 20.29 27.21 41.07
L2 60 11.29 13.60 15.91 18.22 21.68 25.14 32.07 45.93
Z 60 12.16 13.32 14.47 15.63 17.36 19.09 22.55 29.48
MINIMUM H = 7.53
Y 90 1.50 3.50 6.50 9.50 15.50 27.50
L1 90 13.01 16.01 22.01 34.01
L2 90 20.30 23.30 29.30 41.30
Z 90 12.62 12.62 12.62 12.62
MINIMUM H = 12.62
HEIGHT – H
DIM ANGLE 2" 4" 6" 8" 10" 12" 15" 18" 24" 36"
Special Bending Information Chart (cont’d)