Greenlee 555 - Special Bending Information Chart (Continued); IMC Conduit Bending Data

Greenlee Textron / Subsidiary of Textron Inc.
25
4455 Boeing Dr., Rockford, IL 61109-2988 815/397-7070
555 Electric Bender
HEIGHT – H
DIM ANGLE 2" 4" 6" 8" 10" 12" 15" 18" 24" 36"
1-1/2 IMC Dia. = 1.883 Radius = 8.53 X = 4.28
Y 15 6.41 14.14 21.87 29.60 37.32 48.91 60.51 83.69 130.05
L1 15 7.71 15.44 23.17 30.90 38.62 46.35 57.94 69.53 92.72 139.08
L2 15 9.95 17.68 25.40 33.13 40.86 48.58 60.18 71.77 94.95 141.31
Z 15 13.99 21.45 28.92 36.38 43.85 51.31 62.51 73.70 96.10 140.88
MINIMUM H = 1.69
Y 22.5 2.02 7.24 12.47 17.69 22.92 30.76 38.60 54.28 85.64
L1 22.5 10.41 15.64 20.86 26.09 31.31 39.15 46.99 62.67 94.03
L2 22.5 13.76 18.98 24.21 29.44 34.66 42.50 50.34 66.02 97.38
Z 22.5 17.33 22.16 26.99 31.82 36.64 43.89 51.13 65.61 94.59
MINIMUM H = 2.94
Y 30 3.55 7.55 11.55 15.55 21.55 27.55 39.55 63.55
L1 30 11.90 15.90 19.90 23.90 29.90 35.90 47.90 71.90
L2 30 16.36 20.36 24.36 28.36 34.36 40.36 52.36 76.36
Z 30 19.24 22.71 26.17 29.64 34.83 40.03 50.42 71.21
MINIMUM H = 4.43
Y 45 2.17 5.00 7.83 12.07 16.31 24.80 41.77
L1 45 13.78 16.60 20.85 25.09 33.57 50.54
L2 45 20.47 23.30 27.55 31.79 40.27 57.24
Z 45 21.35 23.35 26.35 29.35 35.35 47.35
MINIMUM H = 8.02
Y 60 1.26 3.56 7.03 10.49 17.42 31.28
L1 60 16.40 19.87 26.80 40.65
L2 60 25.34 28.80 35.73 49.58
Z 60 22.79 24.52 27.99 34.91
MINIMUM H = 12.24
Y 90 1.25 4.25 10.25 22.25
L1 90 20.34 32.34
L2 90 33.74 45.74
Z90 21.34 21.34
MINIMUM H = 21.34
2 IMC Dia. = 2.36 Radius = 9.46 X = 4.61
Y 15 5.04 12.77 20.50 28.22 35.95 47.54 59.13 82.31 128.68
L1 15 7.71 15.44 23.17 30.90 38.62 46.35 57.94 69.53 92.71 139.08
L2 15 10.19 17.92 25.64 33.37 41.10 48.83 60.42 72.01 95.19 141.56
Z 15 14.56 22.03 29.49 36.96 44.42 51.89 63.08 74.28 96.67 141.45
MINIMUM H = 1.84
Y 22.5 0.88 6.10 11.33 16.56 21.78 29.62 37.46 53.14 84.50
L1 22.5 10.40 15.63 20.86 26.08 31.31 39.15 46.99 62.67 94.02
L2 22.5 14.12 19.35 24.57 29.80 35.02 42.86 50.70 66.38 97.74
Z 22.5 18.03 22.86 27.69 32.52 37.34 44.59 51.83 66.31 95.29
MINIMUM H = 3.20
Y 30 2.50 6.50 10.50 14.50 20.50 26.50 38.50 62.50
L1 30 11.88 15.88 19.88 23.88 29.88 35.88 47.88 71.88
L2 30 16.84 20.84 24.84 28.84 34.84 40.84 52.84 76.84
Z 30 20.07 23.54 27.00 30.46 35.66 40.86 51.25 72.03
MINIMUM H = 4.84
Y 45 1.12 3.94 6.77 11.02 15.26 23.74 40.71
L1 45 13.74 16.56 20.81 25.05 33.53 50.50
L2 45 21.16 23.99 28.24 32.48 40.96 57.93
Z 45 22.45 24.45 27.45 30.45 36.45 48.45
MINIMUM H = 8.80
Y 60 0.11 2.42 5.89 9.35 16.28 30.13
L1 60 16.30 19.77 26.70 40.55
L2 60 26.21 29.67 36.60 50.46
Z 60 24.19 25.93 29.39 26.32
MINIMUM H = 13.45
Y90 2.75 8.75 20.75
L1 90 19.94 31.94
L2 90 34.80 46.80
Z90 23.53 23.53
MINIMUM H = 23.53
Special Bending Information Chart (cont’d)