Greenlee 555 - Special Bending Information Chart (Continued); Rigid Conduit Bending Data

Greenlee Textron / Subsidiary of Textron Inc.
24
4455 Boeing Dr., Rockford, IL 61109-2988 815/397-7070
555 Electric Bender
1-1/2 RIGID Dia. = 1.9 Radius = 8.5 X = 4.8
Y 15 5.87 13.59 21.32 29.05 36.77 48.37 59.96 83.14 129.50
L1 15 7.71 15.44 23.17 30.90 38.62 46.35 57.94 69.53 92.72 139.08
L2 15 9.94 17.67 25.39 33.12 40.85 48.58 60.17 71.76 94.94 141.31
Z 15 14.50 21.97 29.43 36.89 44.36 51.82 63.02 74.21 96.61 141.39
MINIMUM H = 1.82
Y 22.5 1.48 6.71 11.93 17.16 22.38 30.22 38.06 53.74 85.10
L1 22.5 10.41 15.64 20.86 26.09 31.31 39.15 46.99 62.67 94.03
L2 22.5 13.75 18.97 24.20 29.43 34.65 42.49 50.33 66.01 97.37
Z 22.5 17.84 22.67 27.50 32.32 37.15 44.39 51.64 66.12 95.09
MINIMUM H = 3.13
Y 30 3.02 7.02 11.02 15.02 21.02 27.02 39.02 63.02
L1 30 11.90 15.90 19.90 23.90 29.90 35.90 47.90 71.90
L2 30 16.35 20.35 24.35 28.35 34.35 40.35 52.35 76.35
Z 30 19.75 23.21 26.68 30.14 35.34 40.53 50.92 71.71
MINIMUM H = 4.68
Y 45 1.65 4.48 7.31 11.55 15.79 24.28 41.25
L1 45 13.78 16.60 20.85 25.09 33.58 50.55
L2 45 20.45 23.28 27.52 31.77 40.25 57.22
Z 45 21.84 23.84 26.84 29.84 35.84 47.84
MINIMUM H = 8.37
Y 60 0.74 3.05 6.52 9.98 16.91 30.76
L1 60 16.41 19.87 26.80 40.66
L2 60 25.31 28.77 35.70 49.56
Z 60 23.28 25.01 28.47 35.40
MINIMUM H = 12.66
Y 90 0.75 3.75 9.75 21.75
L1 90 20.35 32.35
L2 90 33.70 45.70
Z90 21.80 21.80
MINIMUM H = 21.80
2 RIGID Dia. = 2.375 Radius = 9.78 X = 5.16
Y 15 4.42 12.15 19.87 27.60 35.33 46.92 58.51 81.69 128.06
L1 15 7.71 15.44 23.17 30.89 38.62 46.35 57.94 69.53 92.71 139.08
L2 15 10.27 18.00 25.73 33.46 41.18 48.91 60.50 72.09 95.27 141.64
Z 15 15.20 22.66 30.13 37.59 45.06 52.52 63.72 74.91 97.30 142.09
MINIMUM H = 2.00
Y 22.5 0.24 5.47 10.70 15.92 21.15 28.99 36.83 52.51 83.86
L1 22.5 10.40 15.63 20.85 26.08 31.31 39.15 46.99 62.66 94.02
L2 22.5 14.24 19.47 24.70 29.92 35.15 42.99 50.83 66.51 97.86
Z 22.5 18.71 23.54 28.36 33.19 38.02 45.26 52.51 66.99 95.96
MINIMUM H = 3.46
Y 30 1.84 5.84 9.84 13.84 19.84 25.84 37.84 61.84
L1 30 11.88 15.88 19.88 23.88 29.88 35.88 47.88 71.88
L2 30 17.00 21.00 25.00 29.00 35.00 41.00 53.00 77.00
Z 30 20.79 24.26 27.72 31.19 36.38 41.58 51.97 71.75
MINIMUM H = 5.20
Y 45 0.42 3.25 6.08 10.32 14.57 23.05 40.02
L1 45 13.72 16.55 20.79 25.04 33.52 50.49
L2 45 21.40 24.23 28.47 32.72 41.20 58.17
Z 45 23.26 25.26 28.26 31.26 37.26 49.26
MINIMUM H = 9.38
Y 60 1.68 5.14 8.61 15.54 29.39
L1 60 16.27 19.73 26.66 40.52
L2 60 26.51 29.97 36.90 50.76
Z 60 25.11 26.85 30.31 37.24
MINIMUM H = 14.25
Y90 1.87 7.87 19.87
L1 90 31.80
L2 90 47.16
Z90 24.72
MINIMUM H = 24.72
HEIGHT – H
DIM ANGLE 2" 4" 6" 8" 10" 12" 15" 18" 24" 36"
Special Bending Information Chart (cont’d)