Need help?Do you have a question about the Grundfos CRE and is the answer not in the manual?
General| Protection Class | IP55 |
|---|---|
| Material | Stainless Steel |
| Applications | Water supply, pressure boosting, irrigation |
| Impeller Material | Stainless Steel |
| Pump Housing Material | Stainless Steel |
| Connection Size | DN32 to DN200 (depending on model) |
| Power Supply | 3-phase |
| Control | Integrated frequency converter |
Explains symbols for DANGER, WARNING, CAUTION, and SIGNAL WORD.
Explains symbols for FM, exclamation marks, and tips.
Lists common abbreviations and their definitions.
Describes the E-pumps, their features, and control modes.
Explains nameplate, functional module, and operating panel identification.
Explains serial communication via RS-485 for GENIbus protocol.
Explains the operating status indicated by the Grundfos Eye.
Details the two potential-free signal outputs and their functions.
Provides safety warnings and guidelines for transporting the pump.
Instructions for checking the product upon receipt.
Guidelines for manual lifting and handling, including safety precautions.
Instructions for securely mounting the product to a foundation.
Refers to technical data for cable entry and gland sizes.
Details requirements for adequate motor cooling and air circulation.
Provides guidelines for outdoor installation, including covers and heating.
Explains the purpose and use of drain holes for condensation.
Step-by-step guide to rotating the operating panel by 180 degrees.
Covers grounding, protective conductors, and voltage transient protection.
Specifies conductor types, materials, and cross-sections.
Details single-phase and three-phase power supply requirements and connections.
Discusses overvoltage, undervoltage, overload, and phase unbalance protection.
Provides an overview of pump connections, inputs, outputs, and terminals.
Guidelines for using screened cables for signal connections.
Instructions for connecting bus cables, including new installations.
Step-by-step guide for installing a CIM module.
Warns about hot surfaces on the product during operation.
Describes the standard operating panel, its symbols, and buttons.
Describes the optional advanced operating panel and its features.
Explains how to set the setpoint for constant pressure and curve modes.
Details pump start/stop and fault reset procedures.
Introduces Grundfos GO Remote for wireless communication and pump control.
Introduces the R100 remote control for pump settings and status display.
Explains how to set the desired setpoint for pump control modes.
Describes available operating modes like Normal, Stop, Manual, Min, Max.
Lists and describes various control modes like Constant Pressure, Flow, etc.
Details the constant pressure control mode and its requirements.
Details the control mode for maintaining a constant flow rate.
Details available analog inputs, their functions, and measured parameters.
Details Pt100/1000 inputs, their functions, and measured parameters.
Explains digital input functions, activation delay, and duration timer modes.
Details configurable digital inputs/outputs and their functions.
Describes the two signal relays for potential-free signaling and their functions.
Explains the analog output for reading operating data to external systems.
Details controller settings like gain (Kp) and integral time (Ti).
Describes influencing the setpoint via external signals.
Details setting limits for parameters and defining actions upon exceeding them.
Describes the low-flow stop function to prevent damage and optimize operation.
Describes the function for smooth startup of systems with empty pipes.
Details setting acceleration and deceleration times for pump speed changes.
Describes monitoring motor bearing condition for replacement/relubrication.
Provides information on service intervals and bearing replacements.
Stores current settings for later use on the same or other pumps.
Guides the user through setting up the pump, including control mode and sensors.
Enables control of multiple pumps in parallel for various operating modes.
Explains the priority of different settings (buttons, digital input, bus) for pump operation.
Lists factory default settings for various pump functions and parameters.
Directs users to download motor service instructions.
Provides information on obtaining pump service documentation.
Details procedures for safely cleaning the pump, including safety warnings.
Specifies maximum start/stop rates and ambient temperature limits.
States humidity limits, actions for high humidity, and motor cooling guidelines.
Details electrical limits, relay specifications, and input/output types.
Covers EMC standards, cable entries, torques, enclosure class, and standby power.
Provides sound pressure level data for different motor sizes and speeds.
Provides specific installation information for USA and Canada, including cURus approval.
Lists relevant electrical codes for USA and Canada.
Details FCC and IC compliance for radio communication.
Lists FCC and IC identification numbers for the radio module.
Covers conductors, torques, line reactors, short-circuit, and branch-circuit protection.
To Next Page
