Grundfos TPE3 - English (Us) Installation and Operating Instructions; Default Chapter; Table of Contents

English (US)
2
English (US) Installation and operating instructions
Original installation and operating instructions.
CONTENTS
Page
1. Symbols used in this document
3
2. Limited warranty
3
3. Abbreviations and definitions
4
4. General information
4
4.1 Radio communication
4
4.2 Battery
4
5. Delivery and handling
4
5.1 Delivery
4
5.2 Handling
4
6. Applications
5
6.1 Pumped liquids
5
7. Operating conditions
5
7.1 Maximum number of starts and stops
5
7.2 Alternating operation of twin-head pumps
5
7.3 Liquid temperature
5
7.4 Ambient temperature
5
7.5 Operating pressure/test pressure
5
7.6 Inlet pressure
6
7.7 Electrical data
6
7.8 Sound pressure level
6
7.9 Environment
6
7.10 Installation altitude
6
7.11 Air humidity
6
7.12 Motor cooling
6
8. Mechanical installation
7
8.1 Pipework
7
8.2 Terminal box positions
8
8.3 Fitting of pump head
8
8.4 Base plate
9
8.5 Insulation
9
8.6 Frost protection
9
8.7 Ensuring motor cooling
9
8.8 Outdoor installation
9
9. Electrical installation
10
9.1 Protection against electric shock, indirect contact
10
9.2 Power supply
10
9.3 Additional protection
11
9.4 Connection terminals
12
9.5 Signal cables
16
9.6 Bus connection cable
16
10. Startup
16
10.1 Flushing the pipe system
16
10.2 Priming
16
10.3 Starting
17
10.4 Shaft seal run-in
17
11. User interfaces
17
12. Standard control panel
18
12.1 Setpoint setting
18
13. Advanced control panel
20
13.1 Menu structure
20
13.2 Menu overview for advanced control panel
21
14. Grundfos GO Remote
23
14.1 Communication
23
14.2 Menu overview for Grundfos GO Remote
24
15. Description of selected functions
26
15.1 Setpoint
26
15.2 Operating mode
26
15.3 Set manual speed
26
15.4 Control mode
26
15.5 FLOWLIMIT
31
15.6 Automatic Night Setback
31
15.7 Analog inputs
31
15.8 Pt100/1000 inputs
31
15.9 Digital inputs
32
15.10 Digital inputs/outputs
32
15.11 Relay outputs
33
15.12 Analog output
33
15.13 Controller settings
33
15.14 Operating range
34
15.15 Setpoint influence
35
15.16 Monitoring functions
38
15.17 Special functions
38
15.18 Communication
38
15.19 General settings
39
16. Assist
39
16.1 Multi-pump setup
39
17. Selection of control mode
40
18. Changing the position of the control panel
42
19. Bus signal
43
20. Priority of settings
43
21. Grundfos Eye
44
22. Signal relays
45
23. Maintenance and service
46
23.1 Maintenance
46
23.2 Service
46
24. Fault finding
47
25. Megging
48
26. Technical data, single-phase motors
48
26.1 Supply voltage
48
26.2 Leakage current
48
27. Technical data, three-phase motors
48
27.1 Supply voltage
48
27.2 Leakage current
48
28. Inputs/outputs
48
29. Other technical data
49
29.1 Torques
49
29.2 Sound pressure level
49
30. Disposal
49