Hach BioTector B3500ul - 8.3 SYSTEM CONFIGURATION MENU

167 pages

To Next Page

To Previous Page

Page 109

8.3 SYSTEM CONFIGURATION MENU

System Configuration menus are used to configure the system in the factory. The user should avoid any

modifications in these menu settings unless it is absolutely necessary.

System Configuration Menu Diagram

Main Page

Table of Contents2
Safety Precautions5
Information and Safety Signs Used in the Manual5
Precautionary Labels Attached to the Instrument6
Certification Marks Attached to the Instrument7
Potential System Safety Hazards8
Ozone and Toxicity9
First Aid Treatment9
General Safety Precautions10
Précautions Générales de Sécurité10
Electrical and Burn Precautions11
Précautions Relatives À L'électricité Et Aux Brûlures11
Carrier Gas and Exhaust Gas Precautions12
Précautions Relatives Au Gaz Porteur Et D'échappement12
Chemical Precautions13
Précautions Chimiques13
Sample Stream Precautions14
Précautions Relatives Aux Échantillons15
Operator's Manual16
Software Screens and Software Menu Diagram16
Startup State18
System Status Messages18
Analysis Data Screen19
Analysis Graph Screen20
Reagent Status Screen20
Select Level Menu21
Enter Password Menu21
Operation Menu22
Start Stop22
Reagents Setup24
Install New Reagents24
Purge Reagents & Zero25
System Range Data Screen25
Manual Program Menu26
Reaction Archive Screen27
Fault Archive Menu27
Time & Date Menu28
Contact Information28
LCD Adjust28
Calibration Menu29
Zero Calibration29
Span Calibration31
Technical Specifications34
Introduction37
Biotector Major Components37
Analysis Enclosure37
Motherboard Enclosure40
Biotector Operation42
Biotector Oxidation Method42
Biotector Sample Injection43
Biotector Oxygen Concentrator45
Biotector Analysis Types47
TIC & TOC Analysis47
TC Analysis47
VOC (POC) Analysis48
Installation49
Basic System Requirements49
Unpacking and Installation50
Analyzer Dimensions and Mounting51
Wiring Power and Signal Terminals53
Wiring External Power Disconnection Switches55
System Fuse Specifications57
Air Supply and Reagent Connections58
Air Supply Connection59
Reagent Connections60
Sample, Drain and Exhaust Connections62
Sample Inlet Tube Position62
Drain and Exhaust Connections64
Reagents and Calibration Standards65
Reagents65
Calibration Standards66
Analyzer Commissioning and Startup69
Maintenance Menu75
Diagnostics Menu76
Process Test77
Pressure Test77
Flow Test78
Ozone Test79
Sample Pump Test81
Ph Test82
Simulate86
Signal Simulate90
Data Output92
Send Reaction Archive93
Send Fault Archive96
Send Configuration96
Send All Data96
Input/Output Status97
Oxygen Controller Status98
Service99
Commissioning Menu100
Reaction Time100
Sample Pump101
Stream Program101
COD/BOD Program103
New Reagents Program103
Reagents Monitor104
Autocal Program105
4-20Ma Program105
Alarm Program107
Data Program108
Information108
System Configuration Menu109
Analysis Mode110
System Program111
Calibration Data116
Sequence Program116
Average Program116
Zero Program117
Span Program119
Reagents Purge121
Pressure/Flow Test Program121
Output Devices123
System Outputs123
Programmable Outputs125
Reaction Check126
Result Integration127
Fault Setup128
Fault Status131
CO 2 Analyzer132
Cooler Program133
Ozone Destructor Program134
Software Update135
Password136
Language136
Hardware Configuration136
Troubleshooting of System Fault, Warning and Notification Events137
Biotector Fault Event Explanation and Remedial Action137
Biotector Warning Event Explanation and Remedial Action141
Biotector Notification Event Explanation and Remedial Action150
Service and Maintenance151
Weekly Maintenance151
Six Month Service152
System Replacement and Spare Parts157
Warranty and Exclusions160
Appendices161
Appendix 1 Glossary of Terms and Abbreviations161
A 2 C I164

Hach BioTector B3500ul - 8.3 SYSTEM CONFIGURATION MENU

Table of Contents

Related product manuals