Ex manual Rev 0 - Oct 29, 2014 20
3.Installation instructions
3.1. Connection information and start-up
The Hetronic radio remote control may only be connected by a qualified expert familiar with the
machine to be operated (see section 4., “Maintenance”).
Before starting any work switch on the cabinet or the receiver,
switch off the power supply to the machine to be controlled.
HETRONIC will not accept liability or provide a guarantee in the
event of personal injury, damage to property and consequential
damage resulting from improper or negligent handling of this
product or from handling that does not comply with the
regulations and standards on which these operating instructions
are based.
Identify an easily accessible place for the installation of the receiver outside the vehicle, the machine
to be controlled such as a switch cabinet or any other similar equipment. A projecting antenna must
be installed if the receiver is mounted inside a switch cabinet. Suitable antennas can be purchased
from your closest Hetronic dealer.
If this control is equipped with a receiver for the hazardous area,
also the operating manual and instructions attached to this
receiver have to be considered for connection and startup.
3.2. Mounting the receiver
The receiver should be mounted on the vehicle or controlled equipment with the screwed glands or
connections underneath. If your receiver is to be installed on a vehicle or on a mobile machine, four
rubber dampers should be used to minimise machine vibrations from damaging the receiver
electronics. Suitable dampers to match your receiver housing can be purchased from your closest
Hetronic dealer. Drawings of your transmitter and receiver version are included with this manual.
Ex manual Rev 0 - Oct 29, 2014 20
3.Installation instructions
3.1. Connection information and start-up
The Hetronic radio remote control may only be connected by a qualified expert familiar with the
machine to be operated (see section 4., “Maintenance”).
Before starting any work switch on the cabinet or the receiver,
switch off the power supply to the machine to be controlled.
HETRONIC will not accept liability or provide a guarantee in the
event of personal injury, damage to property and consequential
damage resulting from improper or negligent handling of this
product or from handling that does not comply with the
regulations and standards on which these operating instructions
are based.
Identify an easily accessible place for the installation of the receiver outside the vehicle, the machine
to be controlled such as a switch cabinet or any other similar equipment. A projecting antenna must
be installed if the receiver is mounted inside a switch cabinet. Suitable antennas can be purchased
from your closest Hetronic dealer.
If this control is equipped with a receiver for the hazardous area,
also the operating manual and instructions attached to this
receiver have to be considered for connection and startup.
3.2. Mounting the receiver
The receiver should be mounted on the vehicle or controlled equipment with the screwed glands or
connections underneath. If your receiver is to be installed on a vehicle or on a mobile machine, four
rubber dampers should be used to minimise machine vibrations from damaging the receiver
electronics. Suitable dampers to match your receiver housing can be purchased from your closest
Hetronic dealer. Drawings of your transmitter and receiver version are included with this manual.
Ex manual Rev 0 - Oct 29, 2014 20
3.Installation instructions
3.1. Connection information and start-up
The Hetronic radio remote control may only be connected by a qualified expert familiar with the
machine to be operated (see section 4., “Maintenance”).
Before starting any work switch on the cabinet or the receiver,
switch off the power supply to the machine to be controlled.
HETRONIC will not accept liability or provide a guarantee in the
event of personal injury, damage to property and consequential
damage resulting from improper or negligent handling of this
product or from handling that does not comply with the
regulations and standards on which these operating instructions
are based.
Identify an easily accessible place for the installation of the receiver outside the vehicle, the machine
to be controlled such as a switch cabinet or any other similar equipment. A projecting antenna must
be installed if the receiver is mounted inside a switch cabinet. Suitable antennas can be purchased
from your closest Hetronic dealer.
If this control is equipped with a receiver for the hazardous area,
also the operating manual and instructions attached to this
receiver have to be considered for connection and startup.
3.2. Mounting the receiver
The receiver should be mounted on the vehicle or controlled equipment with the screwed glands or
connections underneath. If your receiver is to be installed on a vehicle or on a mobile machine, four
rubber dampers should be used to minimise machine vibrations from damaging the receiver
electronics. Suitable dampers to match your receiver housing can be purchased from your closest
Hetronic dealer. Drawings of your transmitter and receiver version are included with this manual.
To Next Page
Loading...
