Need help?Do you have a question about the HikRobot ID6000 Series and is the answer not in the manual?
General| Image Sensor | CMOS |
|---|---|
| Lens Mount | C-mount |
| Light Source | LED |
| Frame Rate | 60 fps |
| Pixel Size | 3.45 µm x 3.45 µm |
| Barcode Types | 1D, 2D |
| Communication Interface | GigE |
| Interface | Gigabit Ethernet, USB 3.0 |
| Operating Temperature | 0°C to 50°C |
States terms of use, limitations of liability, and responsibilities for product usage.
Details FCC compliance requirements and measures to correct interference.
Confirms product compliance with EU directives and harmonized European standards.
Details environmental conditions for safe operation and storage, avoiding hazards.
Outlines measures to prevent damage from static electricity during handling and installation.
Guidance on proper installation placement to avoid impact and vibration.
Specifies qualifications, knowledge, and skills required for installation and maintenance personnel.
Defines the pins and their functions for the 12-pin interface connector.
Explains the status of PWR, LNK, ACT, and custom indicators (U1, U2).
Describes the opto-isolated input circuit and voltage/current specifications.
Details the opto-isolated output circuit and voltage/current specifications.
Illustrates wiring for PNP and NPN devices connecting to input signals.
Illustrates wiring for PNP and NPN devices connecting to output signals.
Lists required accessories and preparations before installing the device.
Provides step-by-step instructions for physically mounting the device.
Guides on downloading, installing, and configuring the IDMVS client software.
Recommends disabling the Windows firewall for stable client operation and image transmission.
Instructions for configuring the PC's network settings for communication with the camera.
Steps to set the device's IP address to match the PC's network segment.
Procedure for establishing a connection between the camera and the client software.
Explains the different camera modes (Test, Normal, Raw) and their usage.
Guides on adjusting image parameters for optimal quality.
Details how to set exposure time, gain, gamma, and frame rate for image acquisition.
Enables horizontal image reversal function for specific viewing needs.
Instructions for adding and selecting types of barcodes for recognition.
Detailed settings for 1D barcode recognition algorithm parameters.
Detailed settings for 2D barcode recognition algorithm parameters.
Configuration of internal and external trigger modes for image acquisition.
Instructions for enabling external trigger modes and setting parameters.
Configuration for hardware-based trigger modes using input signals.
Setting up trigger signals based on a count of input events.
Using I/O signals to enable or disable triggers.
Stopping triggers using serial port commands.
Stopping triggers using UDP commands.
Stopping triggers based on a maximum output time limit.
Configuring which output lines (LineOut 0, 1, 2) are used for signals.
Selecting events that trigger output signals, like acquisition start/stop.
Configuring output signal when acquisition begins.
Configuring output signal when a frame burst starts.
Configuring output signals based on hardware trigger sources.
Configuring output signals based on timer events.
Configuring output signal upon successful barcode read.
Defines output modes (instant/non-instant) for code reading results.
Sets rules to filter unwanted barcodes and improve reading efficiency.
Configures the format and content of the outputted barcode information.
Configures output parameters for TCP Server communication.
Configures output parameters for Serial communication.
Configures output parameters for HTTP communication.
Configures output parameters for FTP communication.
Settings for enabling Smart SDK protocol and image compression.
Configuration for TCP Client, including output buffer and destination.
Settings for Serial communication protocol, baudrate, data bits, parity, and stop bits.
Configuration for FTP communication, including output buffer and server details.
Instructions on how to start and stop the real-time live view of the camera.
Steps to start and stop acquiring data streams from the device in real-time.
Adding cross lines to the live view image for object positioning.
Guidance on recording video files and capturing images continuously.
Accessing and exporting device logs, including errors and warnings.
Configuring the device to automatically enter operating status upon power-on.
Procedure for updating the device firmware using the client software.
Methods for rebooting the device through the client software.
Troubleshooting steps for when no device is listed in the client software.
Solutions for poor image brightness, suggesting adjustments to light, exposure, and gain.
Troubleshooting steps for poor live view image quality, related to network and packet settings.
To Next Page
