Need help?Do you have a question about the HIKVISION DS-7732NI-I4/16P and is the answer not in the manual?
General| Maximum resolution | 3840 x 2160 pixels |
|---|---|
| Alarm input channels | 16 |
| Video input channels | 32 channels |
| Alarm output channels | 4 |
| Supported resolutions | 3840 × 2160, 2560 × 1440, 1920 × 1080, 1600 × 1200, 1280 × 1024, 1280 × 720, 1024 × 768 |
| Video formats supported | H.264, H.265, MPEG4 |
| Audio RCA inputs | 1 |
| RS-232 interface | Yes |
| Networking standards | IEEE 802.3af, IEEE 802.3at |
| USB 2.0 ports quantity | 2 |
| Ethernet LAN data rates | 10, 100, 1000 Mbit/s |
| Ethernet LAN (RJ-45) ports | 9 |
| Supported network protocols | TCP/IP, DHCP, HIK Cloud P2P, DNS, DDNS, NTP, SADP, SMTP, NFS, iSCSI, UPnP™, HTTPS |
| Power over Ethernet (PoE) ports quantity | 8 |
| HDD capacity | 0 GB |
| HDD interface | Serial ATA |
| Maximum storage capacity | 6 TB |
| Number of HDDs installed | 0 |
| AC input voltage | 100 - 240 V |
| Power consumption (max) | 300 W |
| Power consumption (typical) | 20 W |
| Total Power over Ethernet (PoE) budget | 200 W |
| Operating temperature (T-T) | -10 - 55 °C |
| Operating relative humidity (H-H) | 10 - 90 % |
| Product color | Black |
| Rack capacity | 1.5U |
| Supported graphics resolutions | 1024 × 768, 1280 × 1024, 1920 × 1080 |
Weight and Dimensions| Depth | 390 mm |
|---|---|
| Width | 445 mm |
| Height | 70 mm |
| Weight | 5000 g |
Steps for powering on, shutting down, and activating the NVR device.
Process for setting an administrator password to activate the NVR for first-time access.
Steps to reset the NVR administrator password using a GUID file.
Guided setup process for initial NVR configuration.
Instructions for adding and connecting IP cameras to the NVR system.
Setting up PTZ parameters for camera control.
Configuring camera presets, patrol paths, and movement patterns.
Defining image quality, stream type, resolution, and encoding parameters.
Setting schedules for automatic recording and capture based on time or events.
Setting up motion detection parameters, areas, sensitivity, and actions.
Configuring recording and capture triggered by alarm inputs.
Setting up recording triggered by Video Content Analysis (VCA) events.
Procedures for searching and playing back recorded video files.
Methods for exporting and backing up recorded files to external storage.
Configuring a hot spare device for system redundancy and data reliability.
Configuring motion detection parameters, areas, sensitivity, and schedules.
Handling actions for external sensor alarms, including one-key disarming.
Configuring face detection rules, sensitivity, and saving captured pictures.
Setting up vehicle detection, license plate capture, and alarm signals.
Defining virtual lines for detecting crossing events and setting alarm response durations.
Configuring intrusion detection rules, thresholds, sensitivity, and percentages.
Setting up rules for detecting objects entering a defined virtual region.
Searching for captured face pictures and related video files based on specified criteria.
Searching for captured vehicle license plates and related information.
Setting up basic network parameters like IP address, gateway, and DNS.
Setting up redundant array of independent disks (RAID) for data storage and redundancy.
Restoring degraded arrays automatically or manually using hot spare disks.
Steps to initialize newly installed hard disk drives before use.
Updating the NVR firmware via local backup devices or FTP server.
Common issues and solutions for NVR operational problems.
To Next Page
