–
19
–
EN
2C15
English
3 Press Arrow (o/p) to select “CH TUNING”,
then press Arrow (
B).
4 Press Arrow (o/p) to select “MANUAL”,
then press Arrow (
B).
5 Press Arrow (o/p) to select “POSITION”,
then press Arrow (
B).
• When a weak signal is received in Manual Tuning
mode, you can change the background to solid blue or
the static screen by pressing CLEAR/C.RESET.
6 Press Number,
or
Arrow (o/p) to select
your desired position number, then press
Arrow (
B).
• You can select position number 01-99.
• If [ON] appears on the right side of “SKIP”, press
Arrow (o/p) to point to “SKIP”. Then, press Arrow
(
B) to select [OFF].
• If you want to remove scrambled signals, press Arrow
(
o/p) repeatedly to point to “DECODER”. Then,
press Arrow (B) to select [ON].
7 Press Arrow (o/p) to select “CHANNEL”,
then press Arrow (
B).
8 Press Arrow (o/p) to start scanning.
• The DVD/VCR tuner will begin to search up or down
automatically. When a channel is found, the
DVD/VCR will stop searching and the picture will
appear on the TV Screen.
• You can select desired channel number by using the
Number Buttons. You must refer to the channel plan
and press three digits to select the channel number.
(To select channel 24, first press “0” and then press
“2” and “4”).
•
If this is the channel you want, press
Arrow (B)
.
9 Press MENU to exit.
Note
To confirm that a channel has been added, press PROG
(o/p).
You can programme the tuner to scan only the chan-
nels that you can receive in your area.
• Use the remote control for this procedure.
1 Turn on the TV and select the TV channel to
the video channel on the TV.
2 Press MENU.
3 Press Arrow (o/p) to select “INITIAL”, then
press Arrow (
B).
4 Press Arrow (o/p) to select “CH TUNING”,
then press Arrow (
B).
5 Press Arrow (o/p) to select “AUTO”, then
press Arrow (
B).
• The tuner scans and memorises all the active chan-
nels in your area. After scanning, the tuner stops on
the lowest memorised channel.
To Select a Desired Channel
You can select a desired channel by using
the PROG (o/p), or directly pressing Number on
the remote control.
• Enter a channel numbers as a two-digit number for
the quickest results. For example, to select channel 6,
press 0 and 6. If you only press 6, channel 6 will be
selected after a brief delay.
• You can only select channels 1–99.
VCR
MENU
TIMER
SET UP
INITIAL
INITIAL
CH TUNING
CLOCK
RF OUT
LANGUAGE
GUIDE CHANNEL
CH TUNING
AUTO
MANUAL
MOVE
• Use the remote control for this procedure.
1 Press MENU.
2 Press Arrow (o/p) to select “INITIAL”, then
press Arrow (
B).
VCR
MENU
TIMER
SET UP
INITIAL
INITIAL
CH TUNING
CLOCK
RF OUT
LANGUAGE
GUIDE CHANNEL
CH TUNING
AUTO
MANUAL
MOVE
MANUAL
POSITION
CHANNEL
DECODER
SKIP
P08
008
[OFF]
[OFF]
AUTOMATIC TUNING
MANUAL TUNING
Channel Plan
CH Indication TV Channel
02 – 12 E2 – E12
13 – 20 A – H (only ITALY)
21 – 69 E21 – E69
74 – 78 X, Y, Z, Z+1, Z+2
80 – 99,100 S1 – S20,GAP
121 – 141 S21 – S41
This DVD/VCR can receive Hyper and Oscar frequency bands.
H9550ED.qxd 03.5.20 3:07 PM Page 19
To Next Page
Loading...
