Hitachi UX Twin Nozzle - Page 33

31
Input Register data configuration (4/9)
Word
address
Classification Item name Setting range Contents
0B 0A
Communicati
on
environment
setup
Baud rate(Private port) 0 to 10
Gets the baud rate of the private
port.
0B 0B Data length(Private port) 0 , 1
Gets the data length of the
private port.
0B 0C Parity bit(Private port) 0 to 2
Gets the parity bit of the private
port.
0B 0D Stop bits(Private port) 0 , 1
Gets the stop bits of the private
port.
0B 0E Number of comm. bytes 0 , 1
Gets the number of comm. bytes.
0:1 byte , 1:2 bytes
0B 0F BCC code handling 0 , 1
Gets the BCC code handling.
0:Disable , 1:Enable
0B 10 Communication mode 0 , 1
Gets the communication mode.
0:overwrite-protected
1:overwrite-enabled
0B 11 Print message transfer ACK 0 , 1
Gets the print message transfer
ACK.
0:t=fixed , 1:t=async.
0B 12 Print spec transfer char height 0 , 1
Gets the print spec transfer char
height.
0:2 digits , 1:3 digits
0B 13
Buffer function
(Function item for
Communication buffer)
0 , 1
Gets the buffer function.
0:Disable , 1:Enable
0B 14
Buffer repeat count
(Function item for
Communication buffer)
1 to 9999 Gets the buffer repeat count.
0B 15
Empty Buffer Fault
(Function item for
Communication buffer)
0 , 1
Gets the empty buffer fault.
0:Disable , 1:Enable
0B 16
Timing of Fault
(Function item for
Communication buffer)
0 , 1
Gets the timing of fault.
0:Print Start, 1:Print. Complete
0B 17
Data Number at Fault
(Function item for
Communication buffer)
0 to 9 Gets the data number at fault.
0B 18
Start output
(Function item for SOP-04)
0 , 1
Gets the start output.
0:Disable , 1:Enable
0B 19
Output kind
(Function item for SOP-04)
0 to 2
Gets the output kind.
0:Disable , 1:Print data , 2:Code
0B 1A
Condition
(Function item for SOP-04)
0 , 1
Gets the condition.
0:Every time
1:Different from last time
0B 1B
Status output
(Function item for SOP-04)
0 , 1
Gets the status output.
0:Disable , 1:Enable
0B 1C
Output item(Start item)
(Function item for SOP-04)
1 to 50
Gets the output item. (nozzle 1)
0B 1D
Output item(End item)
(Function item for SOP-04)
1 to 50
0B 1E
Output comm. ENQ
(Function item for SOP-04)
0 , 1
Gets the output comm. ENQ.
0:Disable , 1:Enable
0B 1F
Output port
(Function item for SOP-04)
0 , 1
Gets the output port.
0:Standard port
1:Secondary port
0B 20
Select message
(Function item for SOP-05)
0 , 1
Gets the select message.
0:Disable , 1:Enable
0B 21
Data exchange
(Function item for SOP-05)
0 , 1
Gets the data exchange.
0:Reflect at once
1:Reflect by signal
0B 22 Reserve_1
-
"Reserve" is not initially provided,
but may be added in future.
… …
0B 24 Reserve_3