Honeywell DACT-E3 - User Manual

DACT-E3
Digital Alarm Communicator Transmitter
Product Installation Document
Document 9000-0581:J6 12/16/2019 ECN 19-0648
Section 1: Description
The DACT-E3 (Digital Alarm Communicator Transmitter) sub-assembly is a digital communications circuit. It transmits and
verifies digital signals over the telephone network to a Central Station. The DACT-E3 is compatible with the following digital
signaling formats, and complies with FCC Part 8, Telecommunications Standards for DC and AC Ringer.
It is used as the communications circuit with the following modules and systems.
The DACT-E3 can be installed in a remote location via a local RS-485 interface. Figure 1.1 illustrates the DACT-E3 sub-assembly
and Figure 1.2 shows the DACT-E3 circuit board PCB.
!
CAUTION 1: STATIC SENSITIVE EQUIPMENT:
THIS EQUIPMENT IS SENSITIVE TO STATIC ELECTRICITY. IT MAY BE DAMAGED IF NOT PROPERLY HANDLED.
TRANSPORT AND STORE THIS UNIT IN A STATIC-SHIELDING BAG.
FAILURE TO OBSERVE THIS REQUIREMENT COULD CAUSE LATENT DAMAGE TO THE EQUIPMENT WHICH
MIGHT NOT MANIFEST ITSELF UNTIL AFTER THE EQUIPMENT IS PLACED IN SERVICE.
!
CAUTION 2: DISCONNECT ALL POWER:
REMOVE ALL SOURCES OF POWER BEFORE SERVICING, REMOVING OR INSTALLING ANY UNITS.
• SIA DC8 • 3+1 2300 Hz • 4+2 2300 Hz • Ademco Contact ID
• SIA DCS20 • 4+2 1400 Hz • 3+1 1400 Hz
E3 Series
®
Systems
Retrofit Kits S3 Series System
• E3 Series Broadband/Classic Systems • IF600 Retrofit B-Slim • S3 Series (Small Addressable Panel)
• ILI-MB-E3 (Intelligent Loop Interface-
Main Board)
• 600 XL Retrofit Kit
• ILI95-MB-E3 (Intelligent Loop
Interface95-Main Board)
• 7200 Retrofit Kit
Figure 1.1 DACT-E3 Transmitter Sub-Assembly Figure 1.2 DACT-E3 Transmitter PCB
1
TB1
TB2
1
T VS2 T VS1
PTC1
PTC2
1
TP4
+
+
1
4
STANDBY
LINE2
STAT US
LINE1
STA TUS
TP1
TP2
LED3 LED2 LED1
+
TP3
T1

Honeywell DACT-E3 Specifications

General

Brand	Honeywell
Model	DACT-E3
Category	Transmitter
Language	English

Summary

DACT-E3 Product Description

DACT-E3 Installation Overview

Installation Standards and Compliance

Details NFPA and UL standards for DACT-E3 installation.

General Installation Requirements

Specifies environmental, mounting, and servicing space requirements for DACT-E3.

DACT-E3 Installation Procedures

DACT-E3 Removal and Inspection

Steps for safely removing the unit from packaging and checking for damage.

DACT-E3 Cabinet and Mounting Options

Lists compatible systems, cabinets, and mounting plates for DACT-E3.

DACT-E3 Mounting in E3 Series Cabinets

E3 Series Cabinet Mounting Instructions

Step-by-step guide for installing DACT-E3 in E3 Series cabinet configurations.

DACT-E3 Mounting in S3 Series Cabinets

S3 Series Cabinet Mounting Instructions

Step-by-step guide for installing DACT-E3 in S3 Series cabinets.

DACT-E3 Specifications and Wiring

DACT-E3 Electrical Specifications

Lists operating voltage, current, temperature, and humidity ratings.

DACT-E3 Wiring Terminals

Details the function and designation of each terminal on the DACT-E3.

DACT-E3 Communication Formats and Codes

DACT-E3 Communication Functions

Describes the functions the DACT-E3 performs for communication.

Contact ID Event Reporting Codes (CAMWorks)

Explains Contact ID event reporting codes configured via CAMWorks.

DACT-E3 Standard Contact ID Codes

Standard Contact ID Reporting Code Table

Lists standard Contact ID event reporting codes for various events.

DACT-E3 Custom Contact ID Codes

Custom Contact ID Format Examples

Illustrates custom Contact ID reporting codes for different system types.

DACT-E3 Non-SLC Device Codes

Non-SLC Device Event Codes Table

Lists extended reporting codes for events not originating from SLC devices.

DACT-E3 Telephone Requirements

Telephone Line Requirements and Testing

Details REN requirements, line testing, and compatibility with FCC Part 8.

DACT-E3 Reference Documentation