Honeywell L5210 Series Installation And Startup Guide

LYNX Touch Installation and Setup Guide
- 19 -
Installing Wireless Zones
5800 Series Transmitter Loop Numbers
(Refer to this information when programming transmitters)
The following illustration shows the compatible transmitters, their associated input types and loop
designations.
LOOP 1
5806/5806W3/5807
5808/5808LST/5808W3
EN RO L L AS
SU PE R VI SE D
LOOP 1
LOOP 1
5809
EN RO L L AS
SU PE R VI SE D
58 1 8 M NL
EN RO L L AS
SU PE R VI SE D
LOOP 1
LOOP 1
LOOPS
1 - 3
LOOP 1
LOOP 1
5814
EN RO L L AS
SU PE R VI SE D
5800-002-V4
5804E
ENROLL AS BUTTON
58 2 2 T
EN RO L L AS
SU PE R VI SE D
58 7 7
58 1 6 M N
EN RO L L AS
SU PE R VI SE D
LOOP 1
(TERMINALS)
ALTERNATE
POSITION
FOR LOOP 2
LOOP 2
(REED)
LOOP 3
(TERMINALS)
58 2 8 / 58 28 V
PR OG RA M
HOUSE ID
58 2 1
EN RO L L AS
SU PE R VI SE D
58 2 0 L
EN RO L L AS
SU PE R VI SE D
58 1 9 S ( WH S & BR S )
EN RO L L AS
SU PE R VI SE D
LOOP 1
(INTERNAL
SHOCK
SENSOR
LOOP 2
(REED)
58 1 9
EN RO L L AS
SU PE R VI SE D
LOOP 2
(REED)
LOOP 3
(TERMINALS)
LOOP 1
(TERMINALS)
58 0 0 WAV E
PR O G RA M
HO US E I D
58 0 0 P IR -O D
EN RO L L AS
SU PE R VI SE D
58 0 0 P IR /5 80 0 P I R- CO M
EN RO L L AS
SU PE R VI SE D
58 1 1
EN RO L L AS
SU PE R VI SE D
58 0 0 P IR -R ES
EN RO L L AS
SU PE R VI SE D
58 0 0 M ic ra
EN RO L L AS
SU PE R VI SE D
58 0 0 C O
EN RO L L AS
SU PE R VI SE D
58 0 0 S S1
EN RO L L AS
SU PE R VI SE D
58 0 0 R L
SE T HO U SE I D
LOOP 1
LOOP 1
(LOW
SENSITIVITY
LOOP 2
(HIGH
SENSITIVITY)
LOOP 3 (TEMP)
LOOP 4 (TAMPER)
LOOP 1
(HIGH
SECURITY)
LOOP 2
(STANDARD
SECURITY)
LOOP 3 (TILT MODE)
LOOP 4 (TAMPER)
LOOP 1
(LOW
SENSITIVITY
LOOP 2
(HIGH
SENSITIVITY)
LOOP 3 (TEMP)
LOOP 4 (TAMPER)
5834-4
ENROLL AS BUTTON
LOOP
1
LOOP
1
LOOP
1
LOOP
1
58 7 8
ENROLL AS BUTTON
5870API
EN RO L L AS
SU PE R VI SE D
5869
EN RO L L AS
SU PE R VI SE D
58 5 3
EN RO L L AS
SU PE R VI SE D
ARMED
READY
MESSAGE
MIC
LOOP 1
(LOW SENSITIVITY)
LOOP 2
(HIGH SENSITIVITY)
58 9 8
EN RO L L AS
SU PE R VI SE D
LOOP 4
LOOP 1
LOOP 2
LOOP 3
SERIAL #1
LOOP 3
SERIAL #1
LOOP 4
SERIAL #2
LOOP 3
SERIAL #1
LOOP 2
SERIAL #1
LOOP 1
SERIAL #2
LOOP 2
3
AWAY
STAY
1
2
4
OFF
ON
SERIAL #1
LOOP 4
SERIAL #2
LOOP 1
SERIAL #2
LOOP 2
SERIAL #2
LOOP 3
SERIAL #1
LOOP 1
SERIAL #2
LOOP 4
LOOP 3
58 1 6
EN RO L L AS
SU PE R VI SE D
LOOP 1
(TERMINALS)
LOOP 2
(REED)
Notes: (1) The 5806W3 smoke detector must be used in SIA applications.
(2) Button type devices send only fault and low battery signals; no restore or check-in signals.
Supervised devices send periodic check-in signals, faults, restore and low battery signals.
Unsupervised devices send periodic check-in signals, faults, restore and low battery signals but the control does not supervise
the check-in signals.
(3) If an external sounder is required, the 5800WAVE should be used.
(4) The 5804E and 5834-4 encrypted (High-Security) devices must be activated while the system is in Go-No-Go Test Mode. Refer
to the transmitter’s Installation Instructions for complete details. The system will confirm the enrollment of the encrypted device
by beeping two times
(5) The 5800PIR-OD, 5800RL, 5800SS1, 5804E, 5814, 5821, 5828/5828V, 5877, and 5878 wireless transmitters have not been
evaluated by ETL.

Honeywell L5210 Series Specifications

General

Brand	Honeywell
Model	L5210 Series
Category	Security System
Language	English