Why Honeywell MK7580-30B41-00 - Metrologic MS7580 Genesis powers up, but does not scan and/or beep?
If your Honeywell Barcode Reader powers up but doesn't scan or beep, the bar code symbology you're trying to scan might not be enabled. By default, UPC/EAN, Code 39, interleaved 2 of 5, Code 93, Code 128, Codabar, and PDF are enabled. Check to ensure that the specific type of bar code you are trying to read is enabled in the settings.
Why is the data transmitted to the host incorrect when Honeywell MK7580-30B41-00 - Metrologic MS7580 Genesis Barcode Reader scans?
If your Honeywell Barcode Reader scans, but the data transmitted to the host is incorrect, verify that the imager’s data format matches that required by the host system. Also, ensure that the imager is connected to the proper host port.
What to do if Honeywell Barcode Reader powers up, but does not scan and/or beep?
If the Honeywell Barcode Reader powers up but doesn't scan or beep, it might be because the imager is trying to scan a barcode that does not match the configured criteria. Verify that the bar code being scanned falls into the configured criteria such as character length lock or minimum bar code length settings.
Why Honeywell MK7580-30B41-00 - Metrologic MS7580 Genesis Barcode Reader scans but the data is not correct?
If your Honeywell Barcode Reader scans, but the data is not correct, the configuration might not be set correctly. Ensure that the proper PC type AT, or PS2 is selected. Verify the correct country code and data formatting are selected. You may also need to adjust the inter-character delay symptom.
How to troubleshoot no LEDs, beep or illumination on Honeywell MK7580-30B41-00 - Metrologic MS7580 Genesis Barcode Reader?
If your Honeywell Barcode Reader has no LEDs, beep, or illumination, it might be due to no power being supplied to the imager. Check the transformer, outlet, and power strip. Also, make sure the cable is properly plugged into the imager.
What to do if Honeywell MK7580-30B41-00 - Metrologic MS7580 Genesis Barcode Reader scans a bar code, but locks up after the first scan and the white LED stays on?
If the Honeywell Barcode Reader scans a bar code but locks up after the first scan and the white LED stays on, it could be that the imager is configured to support some form of host handshaking but is not receiving the signal. If the imager is setup to support ACK/NAK, RTS/CTS, or XON/XOFF, verify that the host cable and host are supporting the handshaking properly.
How to troubleshoot Honeywell MK7580-30B41-00 - Metrologic MS7580 Genesis Barcode Reader that powers up OK and scans OK but does not communicate properly with the host?
If your Honeywell Barcode Reader powers up and scans OK but does not communicate properly with the host, check to make sure that the cable is connected to the correct com port.
Why Honeywell MK7580-30B41-00 - Metrologic MS7580 Genesis Barcode Reader powers up OK and scans OK but does not communicate properly with the host?
If your Honeywell Barcode Reader powers up and scans OK but does not communicate properly with the host, the com port at the host might not be working or configured properly. Check to make sure that the baud rate and parity of the imager and the communication port match and the program is looking for 'RS232' data.
What to do if Honeywell MK7580-30B41-00 - Metrologic MS7580 Genesis Barcode Reader scans the bar code but there is no data?
If your Honeywell Barcode Reader scans the bar code but there is no data, make sure the imager is configured for the appropriate mode.
Why Honeywell MK7580-30B41-00 - Metrologic MS7580 Genesis has no LEDs, beep or Illumination?
If your Honeywell Barcode Reader shows no LEDs, beep, or Illumination, it might be because the USB host is not active. The device will not operate from hub/host power without host communication. Turn on the host device and verify adequate power is being supplied to the imager.
General| Brand | Honeywell |
|---|---|
| Model | MK7580-30B41-00 - Metrologic MS7580 Genesis |
| Category | Barcode Reader |
| Language | English |
High-performance presentation area-imaging bar code imager utilizing CMOS sensors.
Details of the standard components included in the MS7580 imager base kit.
Lists available optional accessories, such as AC to DC power transformers.
Instructions for connecting the imager using the RS232 interface.
Steps for installing the imager using the Keyboard Wedge interface.
Procedure for connecting the imager via the RS485 interface.
Guide for connecting the imager using the USB interface.
Lists and illustrates components included in the MS7580 adapter kit.
Lists and illustrates components included in the MS7580 wall mount kit.
Step-by-step guide for attaching the adapter plate and base plate to the imager.
Steps for drilling pilot holes and securing the wall mount to the surface.
Explains the two main modes: Pass-through Scanning and Presentation Scanning.
Describes the different beeps and tones indicating imager status.
Explains the meaning of different LED states (colors, flashing, steady).
Lists failure indicators like 'Long Razzberry Tone' and their causes.
Illustrates and specifies the imager's field of view dimensions.
Provides data on scan depth based on barcode element width for different symbologies.
Shows the area where the object detection sensor activates the imager.
Details the imager's illumination source angles and dimensions.
Shows the imager's IR source angles and dimensions.
Illustrates the imager's targeting source angles and dimensions.
Lists operational specifications like light source, pulse duration, depth of scan field, field of view.
Details physical dimensions, weight, and termination type of the imager.
Specifies input voltage, power consumption, and current ratings.
Lists operating and storage temperature, humidity, light levels, and shock resistance.
Lists selectable keyboard types (AT, IBM PS2) for PC keyboard wedge interface.
Lists supported keyboard country layouts for configuration.
Describes three methods for configuring the imager: Bar Codes, MetroSet2, and Serial Programming.
Details the process and requirements for updating the imager's firmware.
Instructions for connecting the RF EAS antenna cable to the imager.
Provides details for connecting the imager to Checkpoint EAS systems.
Steps to enable and configure EAS system support and signal modes.
Describes precautions and the expected range for deactivating EAS tags.
General pinout information for the MS7580 imager across different interfaces.
Details pin configurations for RS232, RS485, and USB cables at the host end.
Pinout details for the Keyboard Wedge VLink cable and its adapter.
Covers safety information related to LED exposure and general precautions.
Details electromagnetic compatibility (EMC) standards for emissions and immunity.
Specifies compliance for Class A devices when scanner cable is extended.
Specifies compliance for Class B devices when scanner cable is shorter than 3 meters.
To Next Page