HP Enterprise ProLiant MicroServer Gen10

To Next Page

To Previous Page

4. Remove the system board assembly screw.

5. Place a finger in the notch on both sides of the system board assembly, and then pull out the assembly.

Operations 34

Main Page

Table of Contents3
Component Identification6
Front Panel Components6
Front Panel Leds and Buttons7
Rear Panel Components8
Rear Panel Leds9
System Board Components10
DIMM Slot Locations11
DIMM Identification11
Pcie Slot Description13
Drive Numbering14
Drive Screws15
Setup16
Optional Services16
Initial Server Installation16
HPE Installation Service16
Setting up the Server17
Optimum Environment20
Site Requirements20
Space and Airflow Requirements20
Temperature Requirements20
Power Requirements20
Electrical Grounding Requirements21
Server Warnings and Cautions21
Electrostatic Discharge22
Setting up RAID Using the Marvell BIOS Utility22
Setting up RAID Using the HPE Rapid Setup Software24
Installing an Operating System24
Install an os Using the HPE Rapid Setup Software25
Install an os from a Bootable Installation Media25
Operations26
Power up the Server26
Power down the Server26
Prepare the Server for Hardware Installation or Removal26
Prepare the Server for Operation26
Remove the Front Bezel27
Removing a Locked Front Bezel27
Removing an Unlocked Front Bezel28
Install the Front Bezel29
Remove the Chassis Cover30
Install the Chassis Cover31
Install the System Board Assembly31
Remove the System Board Assembly33
Hardware Options Installation35
Introduction35
Drive Options35
Drive Support Information35
Drive Installation Guidelines35
Installing an LFF Drive36
Installing an SFF Drive37
Media Bay Options41
Installing an SSD41
Installing an Optical Drive45
Memory Support49
DIMM Population Information49
DIMM Handling Guidelines50
DIMM Installation Guidelines50
Installing a DIMM50
Storage Controller Options51
Installing a Smart Array Storage Controller51
Expansion Board Options52
Installing an Expansion Board53
Internal USB Device Options56
Install an Internal USB Device56
External HPE RDX Backup System Option57
HPE Trusted Platform Module57
Trusted Platform Module (TPM) - China Import Restrictions58
HPE Trusted Platform Module Guidelines58
Installing the Trusted Platform Module Overview58
Installing the Trusted Platform Module Board59
Retaining the Recovery Key/Password60
Enabling the Trusted Platform Module60
Cabling62
Cabling Overview62
Four-Bay Non-Hot-Plug Drive Cabling62
SSD Cabling63
Optical Drive Cabling64
Fan Cabling65
Power Supply Cabling65
Software and Configuration Utilities66
Server Mode66
Product Quickspecs66
Aptio Setup Utility66
Using the Aptio Setup Utility66
Boot Option Control67
Restoring and Customizing Configuration Settings67
Clearing the BIOS Configuration Settings68
Embedded UEFI Shell69
Secure Boot Configuration70
Marvell BIOS Utility70
Accessing the Marvell BIOS Utility under UEFI Boot Mode70
Accessing the Marvell BIOS Utility under Legacy Boot Mode70
Marvell Storage Utility71
Installing the Marvell Storage Utility71
HPE Smart Storage Administrator71
USB Support72
Keeping the System Current72
Firmware72
Firmware Update72
Drivers, Firmware, and Software Updates74
Operating System Version Support74
HPE Pointnext Portfolio74
Proactive Notifications75
Troubleshooting76
Troubleshooting Resources76
System Battery Replacement77
System Battery Information77
Replacing a System Battery77
Replace the System Battery77
Safety, Warranty, and Regulatory Information79
Regulatory Information79
Notices for Eurasian Economic Union79
Turkey Rohs Material Content Declaration80
Ukraine Rohs Material Content Declaration80
Warranty Information80
Specifications81
Environmental Specifications81
Server Specifications81
Power Supply Specifications81
200 W Power Supply Specifications82
Websites83
Support and Other Resources84
Accessing Hewlett Packard Enterprise Support84
Clearcare Technical Support84
Accessing Updates84
Customer Self Repair85
Documentation Feedback85
Acronyms and Abbreviations86

HP Enterprise ProLiant MicroServer Gen10

Table of Contents

Related product manuals