HP P22 G5 User Manual

2
● This monitor meets ROHS requirements. Be sure to use lead-free solder wire when soldering.
● If you must change a capacitor, be sure to match the polarity as printed on the PCB.
● If you must replace a capacitor, make sure the specification and part number match the BOM
and location.
● If you must replace a capacitor, insert new parts carefully to avoid a short circuit caused by the
near pin.
● Do not get the board wet. Water and moisture can cause a short circuit that causes malfunctions.
● To avoid damage, be sure to use lead-free solder.
● When soldering, work quickly to avoid overheating the circuit board.
● Keep the soldering iron tip clean and well tinned when replacing parts.
● After repair, perform a close inspection of the circuit board to confirm it is in good condition.
● After repair, perform a function test to confirm the power supply is working properly.
ERP Lot5 requirement
1. A professional repairer must have the technical competence to repair electronic displays and comply
with the applicable regulations for repairers of electrical equipment in the Member States where the
repairer operates. Reference to an official registration system as professional repairer, where such a
system exists in the Member States, shall be accepted as proof of compliance.
2. A professional repairer must have insurance that covers liabilities resulting from repairs, regardless
of whether required by the Member State.
RoHS (2002/95/EC) requirements
Applied to all countries that require RoHS.
The RoHS (Restriction of Hazardous Substance in Electrical and Electronic Equipment Directive) is a legal
requirement by the EU (European Union) for the global electronics industry sold in the EU and other
countries. Any electrical and electronics products launched in the market after June 2006 should meet this
RoHS requirement. Products launched in the market before June 2006 are not required to be compliant
with RoHS parts. If the original parts are not RoHS complaint, the replacement parts can be non-ROHS
complaint. If the original parts are RoHS compliant, the replacement parts MUST be RoHS complaint.
If product service or maintenance requires replacing parts, confirm the RoHS requirement before
replacement.
General descriptions
This manual contains general information. There are two levels of service:
Level 1: Cosmetic/appearance/alignment service
Level 2: Circuit board or standard parts replacement

HP P22 G5 Specifications

General

Color gamut	72 %
Pixel pitch	0.25 x 0.25 mm
Screen shape	Flat
Display diagonal	21.5 \
Surface hardness	3H
Anti-glare screen	Yes
Display technology	-
Native aspect ratio	16:9
Vertical scan range	48 - 75 Hz
Maximum refresh rate	75 Hz
Horizontal scan range	30 - 86 kHz
Contrast ratio (dynamic)	8000000:1
Display number of colors	16.7 million colors
Display brightness (typical)	250 cd/m²
Supported graphics resolutions	640 x 480 (VGA), 720 x 400, 800 x 600 (SVGA), 1024 x 768 (XGA), 1280 x 1024 (SXGA), 1280 x 720 (HD 720), 1280 x 800 (WXGA), 1440 x 900 (WXGA+), 1600 x 900, 1680 x 1050 (WSXGA+), 1920 x 1080 (HD 1080)
HP segment	Business
Product color	Black
HDMI version	1.4
DisplayPort version	1.2
Tilt angle range	-5 - 23 °
Panel mounting interface	100 x 100 mm
Sustainability certificates	ENERGY STAR
AC input voltage	100 - 240 V
AC input frequency	50 - 60 Hz
Power consumption (max)	25 W
Power consumption (standby)	0.5 W
Power consumption (typical)	20 W
Cables included	AC, HDMI
Package depth	121 mm
Package width	567 mm
Package height	387 mm
Package weight	5240 g

Weight and Dimensions

Depth (with stand)	180.5 mm
Width (with stand)	488.4 mm
Height (with stand)	378.2 mm
Weight (with stand)	3250 g
Depth (without stand)	51.2 mm
Height (without stand)	294.3 mm