EasyManuals Logo

Huawei S6700 Series Configuration Guide

Huawei S6700 Series
664 pages
To Next Page IconTo Next Page
To Next Page IconTo Next Page
To Previous Page IconTo Previous Page
To Previous Page IconTo Previous Page
Page #162 background imageLoading...
Page #162 background image
SwitchB XGE 0/0/2 VLANIF 30 192.168.2.1/24
SwitchC XGE 0/0/1 VLANIF 20 192.168.1.2/24
SwitchC XGE 0/0/2 VLANIF 40 172.16.1.1/24
SwitchD XGE 0/0/1 VLANIF 30 192.168.2.2/24
SwitchD XGE 0/0/2 VLANIF 50 172.17.1.1/24
SwitchE XGE 0/0/1 VLANIF 40 172.16.1.2/24
SwitchF XGE 0/0/1 VLANIF 50 172.17.1.2/24
Configuration Roadmap
The configuration roadmap is as follows:
1. Enable OSPF on each Switch and configure basic OSPF functions.
2. Configure static routes on SwitchD and import them.
3. Configure Area 1 as a stub area. You need to run the stub command on all Switches in
Area 1.
4. Do not advertise Type3 LSAs to the stub area on SwitchA.
Data Preparation
To complete the configuration, you need the following data:
l The ID of the VLAN to which each interface belongs is shown in Figure 4-6.
l The IP address of each interface is shown in Figure 4-6.
l The router ID of each Switch, the OSPF process ID, and the area to which each interface
belongs are as follows:
– The router ID of SwitchA is 1.1.1.1, the OSPF process ID is 1, the network segment of
Area 0 is 192.168.0.0/24, and the network segment of Area 1 is 192.168.1.0/24.
– The router ID of SwitchB is 2.2.2.2, the OSPF process ID is 1, the network segment of
Area 0 is 192.168.0.0/24, and the network segment of Area 2 is 192.168.2.0/24.
– The router ID of SwitchC is 3.3.3.3, the OSPF process ID is 1, and the network segments
of Area 1 are 192.168.1.0/24 and 172.16.1.0/24.
– The router ID of SwitchD is 4.4.4.4, the OSPF process ID is 1, and the network segments
of Area 2 are 192.168.2.0/24 and 172.17.1.0/24.
– The router ID of SwitchE is 5.5.5.5, the OSPF process ID is 1, and the network segment
of Area 1 is 172.16.1.0/24.
– The router ID of SwitchF is 6.6.6.6, the OSPF process ID is 1, and the network segment
of Area 2 is 172.17.1.0/24.
Configuration Procedure
1. 4.14.1 Example for Configuring Basic OSPF Functions.
2. Configure SwitchD to import static routes.
# Import static routes on SwitchD, as follows:
S6700 Series Ethernet Switches
Configuration Guide - IP Routing 4 OSPF Configuration
Issue 01 (2012-03-15) Huawei Proprietary and Confidential
Copyright © Huawei Technologies Co., Ltd.
143

Table of Contents

Other manuals for Huawei S6700 Series

Questions and Answers:

Question and Answer IconNeed help?

Do you have a question about the Huawei S6700 Series and is the answer not in the manual?

Huawei S6700 Series Specifications

General IconGeneral
BrandHuawei
ModelS6700 Series
CategorySwitch
LanguageEnglish

Related product manuals