What causes Faulty monitoring unit on Huawei Inverter?
If your Huawei Inverter displays 'Faulty Monitoring Unit', it may be due to insufficient flash memory or bad sectors. Try turning off the AC output switch and DC input switch, and then turn them on after 5 minutes. If the alarm persists, replace the monitoring board or contact your dealer or Huawei technical support.
What to do for Device fault on Huawei SUN2000 M5?
If your Huawei Inverter is showing a 'Device Fault' alarm, it indicates an unrecoverable internal circuit fault. Try turning off the AC output switch and DC input switch, wait 5 minutes, then turn them back on. If the alarm persists, contact your dealer or Huawei technical support.
What does Built-in PID operation abnormal mean on Huawei SUN2000 M5 Inverter?
If your Huawei Inverter displays 'Built-in PID operation abnormal', it could be due to low output resistance of PV arrays to ground, or low system insulation resistance. For Cause ID = 1, turn off both AC and DC switches, wait, then turn them back on. If the alarm persists, contact support. For Cause ID = 2, check the impedance between the PV array output and ground for shorts or insufficient insulation; rectify if found. If the alarm persists, contact support.
How to fix Phase wire short-circuited to PE on Huawei SUN2000 M5 Inverter?
If your Huawei Inverter is showing a 'Phase wire short-circuited to PE' error, it means the impedance of the output phase wire to PE is low, or the output phase wire is short-circuited to PE. Check the impedance of the output phase wire to PE, find the location with low impedance, and correct the fault.
What does Abnormal residual current mean on Huawei Inverter?
If your Huawei Inverter displays 'Abnormal residual current', it indicates that the insulation impedance on the input side to PE has decreased during operation. If the alarm occurs accidentally, it could be a temporary issue with the external power cable, and the inverter should recover automatically. If the alarm persists or lasts a long time, check the impedance between the PV string and ground to ensure it's not too low.
What to do if Huawei Inverter shows Grid Loss?
If the Huawei Inverter displays a 'Grid Loss' error, it means a power grid outage has occurred. First, the alarm should clear automatically once the power grid recovers. If it doesn't, check to ensure the AC circuit is properly connected and the AC switch is turned on.
Why is my Huawei Inverter showing Cabinet Overtemperature?
If your Huawei Inverter shows 'Cabinet Overtemperature', it means the inverter is overheating. This could be due to poor ventilation, high ambient temperature, or the inverter malfunctioning. Here's what to do: 1. Check the ventilation and ambient temperature where the inverter is installed. 2. If ventilation is poor or the temperature is too high, improve ventilation and heat dissipation. 3. If ventilation and temperature are fine, but the alarm persists, contact your dealer or Huawei technical support.
What causes DC arc fault on Huawei SUN2000 M5 Inverter?
If your Huawei Inverter displays 'DC arc fault', it means the PV string power cables are arcing or have poor contact. Check the PV string cables for any signs of arcing or poor connections.
How to troubleshoot Abnormal Grounding on Huawei SUN2000 M5 Inverter?
If your Huawei Inverter displays 'Abnormal Grounding', it indicates that the neutral wire or PE cable isn't connected, or the inverter's output mode doesn't match the cable connection. Power off the inverter (AC and DC switches off, wait for specified time). Then: 1. Check the PE cable connection. 2. If connected to a TN grid, check the neutral wire connection and its voltage to ground. 3. After powering on, ensure the inverter's output mode matches the cable connection.
What causes String current backfeed on a Huawei Inverter?
If your Huawei Inverter is showing a 'String current backfeed' error, it means there aren't enough PV modules connected in series in the PV string, making its voltage lower than other strings. Here’s how to troubleshoot: 1. Check if the number of PV modules in the affected string is less than in other strings. If it is, wait until the PV string current drops below 0.5 A, turn off all DC switches, and adjust the number of PV modules to match the others. 2. Check if the open-circuit voltage of the PV string is abnormal. 3. Check if the PV string is shaded.
General| Max Efficiency | 98.6% |
|---|---|
| Max Input Voltage | 1100 V |
| MPPT Operating Voltage Range | 200 V - 1000 V |
| Operating Temperature Range | -25°C to +60°C |
| Communication | RS485, 4G (optional) |
Provides overarching safety guidelines and disclaimers for handling the equipment.
Details crucial safety measures to protect individuals during operation and maintenance.
Outlines essential safety practices related to electrical connections and operations.
Specifies the environmental conditions necessary for safe and proper inverter operation.
Covers safe practices for moving, installing, and handling the inverter and its components.
Guides users through the step-by-step process of mounting and installing the inverter.
Highlights safety warnings and precautions before making electrical connections.
Guides users on how to connect the DC input power cables correctly.
Explains the procedures for connecting AC output and signal cables.
Lists critical checks to perform before powering on the system for the first time.
Details the step-by-step procedure for safely powering on the inverter system.
Provides the procedure for safely powering down the inverter before maintenance.
Lists common alarms, their possible causes, and troubleshooting steps.
Guides on how to access the device commissioning screen via the app.
To Next Page
