Hunter ACC-99D

To Next Page

To Previous Page

Junction

Box

Terminal Block:

Red Wire =

"Hot" or Active

120V Black

230V Brown

White (US)

Blue (International)

Terminal Block:

Blue Wire =

Neutral

Controller Power

Switch

Voltage Selector

Switch

Main Page

Default Chapter3
- Table of Contents3
ACC Interface and Key Components9
Wiring Compartment Interior10
Metal Cabinet, Wall Mount Installation11
Connecting AC Main Power, Wall Mount Cabinet12
Metal Cabinet Optional Pedestal Installation13
Plastic Pedestal Installation13
Concrete Base Installation14
Connecting Plastic Pedestal AC Main Power15
- 120 VAC Connection15
Connecting Earth Ground (All Configurations)17
Installing Station Modules18
- Output Modules (ACM600, AGM600)18
- Connecting the Valve Wires19
- Decoder Output Module (ADM99)19
- Connecting Decoder Output Path Wires19
Key Connections20
24 Vac Test Terminal21
Connecting the Master Valve(S) And/Or Pump Start Relay(S)21
Connecting a Rain or Freeze Shut off Device21
Connecting the Hunter Flow Sensor22
Connecting Other Flow Sensors23
Icr Remote Control23
- Multiple Stations Simultaneously23
Connecting to IMMS24
- Dial-Up Telephone (ACC-COM-POTS)24
- Cellular/Gsm (ACC-COM-GSM, GSM-E)25
- UHF Radio25
Power Failures25
Quick Start25
Controller Programming and Operation26
- Using the Information Button26
- Setting Current Date and Time27
- Setting Program Start Times27
- Setting Station Run Time Duration28
- Changing Seasonal Adjust29
- Setting Days to Water29
- Setting Pump and Master Valve Operation30
  - Set Pump and Master Valve Operation31
  - Changing from Normally Closed to Normally on and Location of P/MV31
- Setting Station Cycle and Soak Durations31
  - Set Station Cycle and Soak Durations31
- Cycle and Soak Summary31
Setting Flow Monitoring32
- Step 1: Select the Flow Sensor32
- Step 2: Viewing Real-Time Flow33
- Step 3: Preparing for Flow Learning34
- Step 4: Learning the Flow34
- Step 5: Review and Edit Flow35
- Flow Alarms35
- Alarm Logs36
- Tips on Flow Alarms37
Setting Clik™ Sensor Operation37
- Set Sensor Operation38
Sensor Alarms (Clik Sensors Sen 1-4 Only)39
- Clear Message39
- Sensor Locations40
- Sensor Locations42
Setting Program Overlap Options43
- Option One: Stack or Overlap43
- Option Two: Smartstack43
- Option Three: Ssg/Smartstack43
- Set Station & Program Names44
- Assign Contact Information44
Data History45
- Name a Program (up to 12 Characters and Spaces)45
- Name a Station (up to 12 Characters and Spaces)45
- View Flow Totals45
- View Alarm Logs45
- View Controller Logs46
- View Station Logs46
- Advanced Features46
- View Version and Station Size47
Common Alarm (Attention) Messages48
- Overcurrent48
- Overflow49
- Power Outage/Power Restored50
- Underflow50
Extended Features50
- Contrast Adjustment50
- No Water Window51
  - To Set a no Water Window51
  - No Water Window Rules51
- Delay between Stations52
  - To Set a Delay52
- P/MV Style (Normally Closed/Normally On)52
  - To Change the Normal Condition of P/M Outputs53
- Setting the Flow Sensor Size and Type53
  - Additional Settings for OTHER54
- SSG (Simultaneous Station Group) Setup54
  - Edit an Ssg55
- Adding an Ssg56
  - Deleting an Ssg56
  - Ssg Flow Data56
- SSG Rules56
- Custom Manual Program Setup57
- Custom Manual Rules57
- Start a Custom Manual58
- Test Program58
  - Run a Test Program58
- Easy Retrieve™ Backup59
One Touch Manual Start60
Manual Operation Dial Position60
System off61
Rain off62
Reset63
Decoder Operations (ACC99D Versions)63
- Connecting the 2-Wire Paths63
- Status Lights (ADM-99 Output Module)64
- Decoder Programming64
- Program Decoder Stations64
- Decoder Pump/Master Valves66
- ICD-SEN Sensor Decoder Setup66
- Setup Overview67
  - Connect an HFS Meter to an ICD-SEN67
  - Connect a Clik Sensor to an ICD-SEN67
- SEN/DEC Setup67
Other Special Decoder Functions (Advanced Features)69
- View Decoder Config69
- Display ADM Current70
- Sen/Dec Alarms70
ACC Solar Sync71
- Preparation71
- Installation72
- Setup72
- Sensor Test73
- Assign Programs74
- Sensor Shutdown Programming74
- Sensor Mapping74
- Sensor Shutdown by Program75
- Operation & Adjustment75
- Making Adjustments76
- Increase or Decrease Watering76
- Check Run Times76
- Tracking the Adjustment History (Controller Log)76
- Solar-Sync Sensor Alarms77
- S-Sync Comm Failure78
IMMS-Et and the ACC Controller79
- ET Setup and Operations79
- ET Functions79
- ET Operation79
- ET Sensor Check80
- View ET Sensors80
- ET Alarm Setup80
Event Mode Options (AGC, Surveyor)82
Central Software and ACC-AGC Communication Modules84
- Theory of Operation84
- UHF Radio84
- Hardwired Cable85
Communication Module Installation for Wall Mount Controller85
- Radio Installation, Additional Steps85
- Radio Connections, Additional Steps86
Communication Module Installation for Plastic Pedestal Controller86
- Radio Installation, Additional Steps86
Setup and Addressing the COM Module87
- Set the Controller Address87
- Other Com Setup Functions87
- Master Controller87
- Contrast87
- Radio Type87
- Last MR CMD (Radio Only)87
- DTMF Wait (Radio Only)87
- MR Default Run Time (Radio Only)88
- Modem Type88
- Country Code88
- Hwim88
- Enter Diagnostics88
  - Communications Status Display [MOD RAD HW]88
- Radio Tone Test89
- Ping Test89
- Ping Hub89
- Soft Reset89
- Total Reset89
- Operating the Com Module89
Troubleshooting90
ACC/AGC Log Messages91
- Alarm Log Messages91
- Alarm Log, Missed Irrigation "Mode" Labels91
- Alarm Log, "Reason" Labels92
- Controller Logs92
- Station Logs93
Specifications94
- Dimensions94
- Electrical94
- Features & General Specifications94
Parts95
- Wall Mount Controllers (ACC1200, ACC99D)95
- Communication Modules and Parts95
- Pedestal Controllers (ACC1200PP, AGC1200PP, ACC99DPP, AGC99DPP)96
- ACC/AGC Central System Components (ACC1200, ACC99D, ACC1200PP, AGC1200PP, ACC99DPP, AGC99DPP)96
Index97

Table of Contents

Related product manuals