Need help?Do you have a question about the Hunter PRO-C P2C Series and is the answer not in the manual?
Details on station count, run time, start times, and watering schedules.
Physical size of the controller unit and its NEMA 3R, IP44 rating.
Power input/output, voltage, current ratings, and battery information.
Information on factory default configurations and non-volatile memory retention.
Details on dial positions for running, setting date/time, programs, run times, and days.
Description of battery, reset, terminals, transformer, junction box, and sensor inputs.
Instructions for securely mounting the controller to a wall using screws and anchors.
Safety and electrical considerations for outdoor installations by licensed electricians.
Steps for routing power cables and connecting wires in the outdoor cabinet.
Mandatory safety precautions for AC wiring installation by a licensed electrician.
Information on adding station modules (PCM-300, 900, 1600) for system expansion.
Compatibility with EZDS for hybrid conventional and two-wire operations.
Procedure for inserting and securing PCM modules using the Power Lock feature.
Steps for routing valve wires from the controller to the valves.
How to connect common and control wires using waterproof connectors.
Connecting common wire to COM and control wires to station terminals.
Connecting master valve wires to P/MV and COM terminals on the base module.
Connecting the pump relay common and signal wires to the controller.
Warning about pump current draw not exceeding 0.28A to prevent controller damage.
Connecting sensor wires to SEN-2 and COM terminals for automatic stop.
How 'OFF' appears on the display when the sensor deactivates watering.
Manual single-station function ignores attached sensors and allows watering.
Using the bypass switch to temporarily override sensor status for up to 24 hours.
How the bypass indicator appears on the display when the switch is active.
Installing the SmartPort Connector on the cabinet or in conduit.
Connecting wires to AC1, AC2, and REM terminals for remote control.
How the sensor calculates ET and adjusts irrigation based on weather.
Connecting the wired sensor to SEN terminal #1 on the Pro-C Controller.
Steps to set the year, month, and day using the dial and buttons.
Steps to set the hour and minutes, including AM/PM or 24-hour format.
How to set up to four start times per program (A, B, C) in 15-minute increments.
Procedure to turn off start times or an entire program by setting to OFF.
Setting run times for each station from 1 minute to 6 hours.
Enabling Seconds Mode for run time resolution up to 5 minutes.
Selecting individual days for watering using the + and - buttons.
Choosing to water on odd or even numbered days of the month.
Clarification that 31st and Feb 29th are OFF days for odd day watering.
Setting the number of days between waterings and days remaining in the interval.
Optionally designating specific days as non-watering days within the interval.
Explanation of how non-water days affect interval watering calculations.
Enabling automatic execution of programs by turning the dial to RUN.
Stopping all watering immediately by turning the dial to SYSTEM OFF.
Running a single station manually for a specified duration.
Making global run time changes (5%-300%) without reprogramming.
Starting a program manually by holding the advance button on RUN mode.
Selecting program A, B, C and adjusting stations/run times for manual start.
Enabling or disabling the P/MV circuit for individual stations via PUMP position.
Stopping irrigation for a set period (1-31 days) using SYSTEM OFF and + button.
Configure sensor overrides, delays, and Solar Sync timing for advanced control.
Optimize watering with cycle/soak settings and inter-station delays.
Tools for testing, saving/restoring programs, checking wiring, and resetting the system.
Advanced options to hide programs, run them manually, and use seconds mode.
Troubleshooting display errors like ERR, P ERR, SP ERR, and 'No AC'.
Resolving problems like watering but no flow, or continuous watering.
Troubleshooting rain sensor not stopping irrigation or other sensor-related problems.
Information regarding Class B digital device compliance with FCC Rules.
Measures to take if the equipment causes harmful interference to radio or TV reception.
Product must be used as described and serviced only by trained personnel.
The Hunter Pro-C is a residential and light commercial irrigation controller designed to manage watering schedules efficiently. This modular controller is suitable for both indoor and outdoor installations, offering a range of features for flexible and precise irrigation management.
The Pro-C controller's primary function is to automate irrigation by controlling the operation of sprinkler valves based on programmed schedules. It allows users to set specific watering times, durations, and days, ensuring that landscapes receive the appropriate amount of water. The controller supports conventional wiring for a range of stations and can be expanded with an EZ Decoder System for larger setups. It features a non-volatile memory, which means all programmed data is retained even during power outages, eliminating the need for a backup battery for program retention.
The Pro-C controller is designed for user-friendly operation with a central control dial that provides access to various programming functions.
The Pro-C controller is designed for durability and ease of maintenance.
General| Rain Sensor Compatibility | Yes |
|---|---|
| Number of Programs | 3 |
| Number of Start Times per Program | 4 |
| Warranty | 2 years |
| Voltage | 24 VAC |
| Display | LCD display with backlight |
| Power Source | 24VAC transformer |
| Transformer Input | 120VAC |
| Transformer Output | 24VAC |
| Sensor Inputs | 1 |
| Enclosure Rating | Indoor/Outdoor |
| Watering Days | 7-day scheduling, Odd/Even day scheduling & Cyclical scheduling |
| Start Times | 4 per program |
| Battery Backup | No |
| Station Run Time | 1 minute to 4 hours |
To Next Page