HUSABERG TE 250 EU - 15.5 Refilling with Coolant

To Next Page

To Previous Page

13 WHEELS, TIRES 81

Guideline

Spoke nipple, front wheel M4.5 5… 6 Nm (3.7…

4.4 lbf ft)

Spoke nipple, rear wheel M5 5… 6 Nm (3.7…

4.4 lbf ft)

Torque wrench with various accessories in set (58429094000)

Main Page

Default Chapter4
- Table of Contents4
1 Means of Representation7
- Symbols Used7
- Formats Used7
2 Safety Advice8
- Use Definition - Intended Use8
- Degrees of Risk and Symbols8
- Tampering Warning8
- Safe Operation9
- Protective Clothing9
- Work Rules9
- Environment9
- Owner's Manual10
3 Important Notes11
- Warranty11
- Operating and Auxiliary Substances11
- Spare Parts, Accessories11
- Service11
- Figures11
- Customer Service11
4 View of Vehicle12
- View of Vehicle, Front Left (Example)12
- View of Vehicle, Rear Right (Example)13
5 Serial Numbers14
- Chassis Number14
- Type Label14
- Key Number (te EU/AUS)14
- Engine Number14
- Fork Part Number14
- Shock Absorber Part Number15
6 Controls16
- Clutch Lever16
- Hand Brake Lever16
- Throttle Grip16
- Kill Switch (te EU/AUS)16
- Kill Switch (te USA)16
- Horn Button (te EU/AUS)17
- Light Switch (te EU/AUS)17
- Light Switch (te USA)17
- Turn Signal Switch (te EU/AUS)17
- Emergency off Switch (te AUS)17
- Electric Starter Button (te 250/300 EU/USA)18
- Electric Starter Button (te AUS)18
- Overview of Indicator Lamps (te EU/AUS)18
- Speedometer18
- Speedometer Overview18
- Activation and Test18
- Tripmaster Switch19
- Setting Kilometers or Miles19
- Adjusting the Speedometer Functions19
- Setting the Clock20
- Querying Lap Time20
- Display Mode SPEED (Speed)21
- Display Mode SPEED/H (Operating Hours)21
- Display Mode SPEED/CLK (Clock)21
- Display Mode SPEED/LAP (Lap Time)21
- Display Mode SPEED/ODO (Odometer)22
- Display Mode SPEED/TR1 (Trip Master 1)22
- Display Mode SPEED/TR2 (Trip Master 2)22
- Display Mode SPEED/A1 (Average Speed 1)23
- Display Mode SPEED/A2 (Average Speed 2)23
- Display Mode SPEED/S1 (Stop Watch 1)23
- Display Mode SPEED/S2 (Stop Watch 2)23
- 6.14.19 Table of Functions24
- 6.14.20 Table of Conditions and Menu Activation24
- Opening the Filler Cap24
- Closing the Filler Cap25
- Fuel Tap25
- Choke25
- Shift Lever26
- Kick Starter26
- Foot Brake Lever26
- Side Stand26
- Steering Lock (te EU/AUS)27
- Locking the Steering (te EU/AUS)27
- Unlocking the Steering (te EU/AUS)27
7 Preparing for Use28
- Advice on First Use28
- Running in the Engine29
- Preparing the Vehicle for Difficult Riding Conditions29
- Preparing for Rides on Dry Sand30
- Preparing for Rides on Wet Sand30
- Preparing for Rides on Wet and Muddy Surfaces31
- Preparing for Rides at High Temperature and Slow Speed31
- Preparing for Rides at Low Temperature and in Snow32
8 Riding Instructions33
- Checks and Maintenance Steps When Preparing for Use33
- Starting33
- Starting off34
- Shifting, Riding34
- Braking34
- Stopping, Parking35
- Transport35
- Refueling36
9 Service Schedule37
- Service Work (as Additional Order)38
10 Tuning the Chassis39
- Checking the Basic Chassis Setting with the Rider's Weight39
- Compression Damping of Shock Absorber39
- Adjusting the Low-Speed Compression Damping of the Shock Absorber39
- Adjusting the High-Speed Compression Damping of the Shock Absorber40
- Adjusting the Rebound Damping of the Shock Absorber40
- Measuring the Sag of the Unloaded Rear Wheel41
- Checking the Static Sag of the Shock Absorber41
- Checking the Riding Sag of the Shock Absorber42
- Adjusting the Spring Preload of the Shock Absorber42
- Adjusting the Riding Sag43
- Checking the Basic Setting of the Fork43
- Adjusting the Compression Damping of the Fork44
- Adjusting the Rebound Damping of the Fork44
- Handlebar Position45
- Adjusting the Handlebar Position45
11 Service Work on the Chassis46
- Raising the Motorcycle with the Lift Stand46
- Removing the Motorcycle from the Lift Stand46
- Bleeding the Fork Legs46
- Cleaning the Dust Boots of the Fork Legs47
- Loosening the Fork Protection47
- Positioning the Fork Protection47
- Removing the Fork Legs48
- Installing the Fork Legs48
- Removing the Fork Protector49
- Installing the Fork Protector49
- Removing the Lower Triple Clamp49
- Installing the Lower Triple Clamp50
- Checking the Play of the Steering Head Bearing51
- Adjusting the Play of the Steering Head Bearing52
- Greasing the Steering Head Bearing52
- Removing the Front Fender53
- Installing the Front Fender53
- Removing the Shock Absorber53
- Installing the Shock Absorber54
- Removing the Seat55
- Mounting the Seat55
- Removing the Air Filter Box Lid55
- Installing the Air Filter Box Lid55
- Removing the Air Filter55
- Installing the Air Filter56
- Cleaning the Air Filter and Air Filter Box56
- Sealing the Air Filter Box57
- Removing the Main Silencer57
- Installing the Main Silencer57
- Changing the Glass Fiber Yarn Filling of the Main Silencer58
- Removing the Right Side Cover58
- Installing the Right Side Cover59
- Removing the Fuel Tank59
- Installing the Fuel Tank60
- Checking the Chain for Dirt61
- Cleaning the Chain61
- Checking the Chain Tension61
- Adjusting the Chain Tension62
- Checking the Chain, Rear Sprocket, Engine Sprocket, and Chain Guide63
- Adjusting the Chain Guide65
- Checking the Frame65
- Checking the Swingarm65
- Checking the Throttle Cable Routing66
- Checking the Rubber Grip66
- Additionally Securing the Rubber Grip67
- Adjusting the Basic Position of the Clutch Lever67
- Checking/Rectifying the Fluid Level of the Hydraulic Clutch67
- Changing the Hydraulic Clutch Fluid68
- Removing the Engine Guard69
- Installing the Engine Guard69
12 Brake System71
- Checking the Free Travel of the Hand Brake Lever71
- Adjusting Free Travel of Hand Brake Lever (te EU/AUS)71
- Adjusting the Basic Position of the Hand Brake Lever (te USA)71
- Checking the Brake Discs72
- Checking the Front Brake Fluid Level72
- Adding Front Brake Fluid72
- Checking the Front Brake Linings73
- Changing the Front Brake Linings74
- Checking the Free Travel of the Foot Brake Lever75
- Adjusting the Basic Position of the Foot Brake Lever75
- Checking the Rear Brake Fluid Level76
- Adding Rear Brake Fluid76
- Checking the Rear Brake Linings77
- Changing the Rear Brake Linings77
13 Wheels, Tires79
- Removing the Front Wheel79
- Installing the Front Wheel79
- Removing the Rear Wheel80
- Installing the Rear Wheel80
- Checking the Tire Condition81
- Checking the Tire Air Pressure82
- Checking the Spoke Tension82
14 Electrical System84
- Removing the Battery (te 250/300)84
- Installing the Battery (te 250/300)84
- Recharging the Battery (te 250/300)84
- Changing the Main Fuse (te 250/300)85
- Removing the Headlight Mask with the Headlight86
- Installing the Headlight Mask with the Headlight86
- Changing the Headlight Bulb87
- Changing the Turn Signal Bulb (te EU/AUS)87
- Checking the Headlight Setting88
- Adjusting the Headlight Range88
- Changing the Speedometer Battery88
15 Cooling System90
- Checking the Antifreeze and Coolant Level90
- Checking the Coolant Level91
- Draining the Coolant91
- Refilling with Coolant92
16 Tuning the Engine94
- Checking the Play in the Throttle Cable94
- Adjusting the Play in the Throttle Cable94
- Carburetor94
- Carburetor - Adjusting the Idle Speed95
- Emptying the Carburetor Float Chamber96
- Checking the Basic Position of the Shift Lever97
- Adjusting the Basic Position of the Shift Lever97
- Engine Characteristic - Auxiliary Spring (te 250/300)97
- Engine Characteristic - Setting the Auxiliary Spring (te 250/300)97
17 Service Work on the Engine99
- Checking the Gear Oil Level99
- Changing the Gear Oil99
- Draining the Gear Oil100
- Refilling with Gear Oil100
- Adding Gear Oil101
18 Cleaning, Care103
- Cleaning the Motorcycle103
- Checks and Maintenance Steps for Winter Operation104
19 Storage105
- Preparing for Use after Storage105
20 Troubleshooting106
21 Technical Data108
- Engine108
- Specifications108
- All te 250108
- All te 300109
- Engine Tightening Torques110
- Te 125110
- Capacities111
- Gear Oil111
- Coolant111
- Fuel111
- Chassis112
- Electrical System112
- Tires113
- Fork113
- Shock Absorber114
- Te 125114
- Chassis Tightening Torques115
- Carburetor116
- 21.10.2 te 250 Eu116
- 21.10.3 te aus116
- 21.10.4 te 250 Usa116
- 21.10.5 te 300 Eu117
- 21.10.6 te 300 Usa117
- Carburetor Tuning (te 125)117
- Carburetor Tuning (All te 250)118
- Carburetor Tuning (All te 300)119
- General Carburetor Tuning120
22 Substances121
23 Auxiliary Substances123
24 Standards125
- Index126

HUSABERG TE 250 EU - 15.5 Refilling with Coolant

Table of Contents

Related product manuals