4.4.4.2 Tools - Test - User interface
The
Tools - Test - User interface
menu shows:
•
Keypad
:
1. Push the OK button to start the keypad test.
2. Push a button. The display shows the button that
is pushed.
3. Push the Back button to exit the test.
•
Display
:
1. Push the OK button to start the display test. The
display flashes.
2. Push the Back button to exit the test.
•
Sound
:
1. Push the OK button to start the sound test. The
buzzer emits a short sound signal at the same
time as a note is shown in the display.
2. Push the Back button to exit the test.
4.4.4.3 Tools - Test - Charging station
This function is used to check if there is a signal for A, F,
N and the guide wires.
1. Place the product in the charging station.
Note: The product and the charging station must be
paired.
2. Push the OK button to start the test.
4.4.4.4 Tools - Test - GPS navigation
The
Tools - Test - GPS navigation
menu shows:
•
Enabled (Yes/No)
: GPS navigation can be activated
via
Installation - Lawn coverage - GPS supported
navigation
.
•
Installed (Yes/No)
: If
NO
is shown, make sure that
the GPS module or the Automower
®
Connect
module is correctly installed and that the products
firmware has been updated.
•
Signal quality
: Signal quality shows the strength of
the GPS signal reception. To get a satisfactory
function, signal quality should be
Good
.
•
Map (BUILDING/COMPLETE)
:
BUILDING
is
displayed the first time the product is used or after
the GPS map has been reset. Once the map is
completed,
COMPLETED
will be displayed, which
takes 2 to 5 days.
4.4.5 Tools - Special settings
Note: The
Tools - Special settings
contains settings that
are only available for service personnel.
The
Tools - Special settings
menu shows:
•
Demo
: The setting is used for installations in shops
or exhibitions. The product alternates between short
periods of operation, docking and charging.
•
Installation lock
: If the installation settings lock is
activated, it is not possible to change any settings in
the
Installation
menu.
Note: The installation settings lock must be
deactivated to change any of the installation settings
in the main menu.
4.4.6 Tools - Calibrate
The
Tools - Calibrate
menu shows:
•
Tilt sensor calibration
: If the product does not
operates as expected in slopes it might help to
calibrate the tilt sensor. Place the product on a
horizontal surface and start the calibration.
•
Cutting height calibration
: The cutting height
calibration can be enabled and the calibration set to
start the next time the product starts.
4.5 Quick info (Limited Tools menu)
The
Quick info
menu is a limited
Tools menu
.
When the start page or the main menu is displayed:
1. Push and hold down the 0 key for 2 seconds to
access the
Quick info
menu.
4.5.1 Quick info - Info
The
Quick info - Info
menu has the same sub-menus as
in
Tools
, except for the sub-menu
Motors
. Refer to
Tools
- Info on page 10
.
4.5.2 Quick info - History
The
Quick info - History
menu has 2 sections:
Messages
and
Search times
.
The
History - Messages
menu shows:
•
Fault messages
: The 50 last fault messages
•
Info messages
: The 50 last information messages.
The
History - Search times
menu show the same sub-
menus as in
Tools - History, total - Search times
. Refer
to
Tools - History, total - Search times on page 12
.
4.5.3 Quick info - Advanced
The
Quick info - Advanced
menu shows:
•
Automatic passage handling
: The guide corridor
width is adjusted automatically. If
Auto passage
handling
is disabled, the corridor width settings must
be made manually. To disable the
Auto passage
handling
: Unselect
Auto passage handling
and push
the OK button.
•
Installation shape
:
•
Open
: Applicable in a large open work area with
a small number of obstacles and no passages,
or when the mowing result is uneven in steep
slopes.
•
Normal
: Applicable in a work area with a
moderate number of obstacles and/or passages.
Applicable for most work areas.
•
Complex
: Applicable in work areas with many
obstacles and/or passages.
1582 - 001 - 23.12.2020 Special menus - 13
To Next Page
Loading...
