IBM 3270 Operator's Guide

~278 Quick Reference
• Do Not Enter (Input Inhibited) Messages
>< .::, .. ::.
>< ?+
Time is required for the host system to perform a function. Wait.
Press RESET; then try the operation again.
The
host system has locked your keyboard. Look for a message. Wait or RESET.
>< S"{:~;TEt'''l
><
><
><
><
)(
)(
><
)(
)(
)(
)(
)(
7.:>
7.:t··lUr·'·l
*u '?
-f
~ nn
and
~ nnn
~,"-nn
and
~,,-nnn
PROGnn
and
PROGnnn
Go elsewhere on the screen to take that action. RESET. Move the cursor or take other action.
You have tried to insert more data than this field can hold. RESET. Correct the entry.
You should enter only numerals in this field. RESET. Then enter only numerals.
Only certain numerals can be entered here. RESET.
The function you requested is not available.
Your display station is not operating properly. RESET. If problem persists, refer to the display station
or control unit Problem Determination Guide to determine the appropriate action.
There is a problem with the communication line !between the control unit and the host system.
RESET.
If problem persists, refer to the display station or control unit Problem Determination Guide
to determine the appropriate action.
The control unit detected a programming error in the data it received from the host system. RESET.
If problem persists, refer to the display station or control unit Problem Determination Guide to
determine the appropriate action.
The printer connected to your display station is busy. If ~ is displayed on the right, the printer is
busy printing your work. Wait for the operation to finish, or press DEV CNCL to cancel a pending
print operation. (If the print operation has started, the operation cannot be canceled by the DEV
CNCL key.)
>< C}-CJ.:):: .. :»
)( ~
Same as above except more time is anticipated before your operation is accepted.
The printer assigned to your display station is not working. If ~ is displayed on the right, the
printer stopped while printing your work. Wait or press DEV CNCL to cancel the print operation.
><
)(
X
)(
)(
><
)(
)(
)(
><
)(
)(
7.:><
0-.1
-¥- ,-,
...... 8:··
7.:"
+'?
7.: ... +'?
7.: ..... +'?
7.:'"+'?
7.:
+?
"
-:S
0+-00
-f .xX
~2>:.:>:;
}
You are not aut:,orized to do that function. RESET.
Security key lock
is off. Keyboard can be unlocked only by key.
That magnetic stripe card cannot be used in this operation. RESET. Try a different card, or request
help.
You have
entered an invalid accent and character combination. RESET. Then rekey both the accent -
and the character. (Canadian French keyboard only.)
The symbol key you pressed is not available. RESET.
A message
from the control operator was received and rejected. RESET
The application program will not allow you to make that selection.
Your display station is not configured for that selection .
• Reminders
~nn - The communication link connecting your control unit to the host system is producing errors.
and
~nnn
Cl+-{!] - Reserved for future use. Ignore .
• Shifts and Modes Messages
Programmed Symbols Selection
SO No Programmed Symbols Selected
PSA Programmed Symbols - Set A
PS'B Programmed Symbols - Set B
PSC Programmed Symbols - Set C
PSD Programmed Symbols - Set D
PSE Programmed Symbols - Set E
PSF Programmed Symbols - Set F
* * You have selected a Programmed Symbol Set
* ~ Field Inherit for Programmed Symbols
*If neither symbol is present, the selection you made is not available at your display station.
Chapter 2. Controls and Indicators 2-3

IBM 3270 Specifications

General

Brand	IBM
Model	3270
Category	Desktop
Language	English