Icom IC-756PRO - Programmed Scan Operation; F Scan Operation

57
7
SCANS
■ Programmed scan operation
q Push [EXIT] one or more times to close a multi-
function screen, if necessary.
w Select VFO mode.
e Select the desired operating mode.
•The operating mode can also be changed while scan-
ning.
r Push [(F-4)SCAN] to select the scan screen.
t Set [RF/SQL] open or closed.
•See previous page for scan condition.
•If the [RF/SQL] control function is set as “AUTO,” the
squelch is always open in SSB, CW and RTTY modes.
See pgs. 3, 68 for details.
y Push [(F-1)PROG] to start the programmed scan.
•Decimal points blink while scanning.
u When the scan detects a signal, the scan stops,
pauses or ignores it depending on the resume set-
ting and the squelch condition.
i To cancel the scan, push [(F-1)PROG].
If the same frequencies are programmed into the
scan edge memory channel P1 and P2, pro-
grammed scan does not start.
ANTANT
1
METERMETER
PoPo
P.AMPP.AMP
1
ATTATT
OFFOFF
VOXVOX
OFFOFF
COMPCOMP
OFFOFF
WIDEWIDE
SFTSFT
0
FIL2FIL2
USBUSB
qw:pp
AGCAGC
MIDMID
TXTX
VFOVFO
USBUSB
USBUSB
USBUSB
FIL2FIL2
qr≥qot≥pp
qr≥wpt≥pp
14.100.0014.100.00
14.100.0014.100.00
1
1
VFOVFO
BWBW
2.4k2.4k
PROGPROG
∂
F FINEFINE
∂
F SPANF SPAN
SETSET
SCANSCAN
PROGRAM SCANPROGRAM SCAN
∂ F  SpanSpan: ±±10kHz10kHz
ProgrammedProgrammed P1:P1:0.500.00MHz0.500.00MHz
scanscan edgesedges P2:P2: 29.999.99MHz29.999.99MHz
ANTANT
1
METERMETER
PoPo
P.AMPP.AMP
1
ATTATT
OFFOFF
VOXVOX
OFFOFF
COMPCOMP
OFFOFF
WIDEWIDE
SFTSFT
0
FIL2FIL2
USBUSB
qw:pp
AGCAGC
MIDMID
TXTX
VFOVFO
USBUSB
USBUSB
USBUSB
FIL2FIL2
qr≥qot≥pp
qr≥wpt≥pp
14.100.0014.100.00
14.100.0014.100.00
1
1
VFOVFO
BWBW
2.4k2.4k
PROGPROG
∂
F FINEFINE
∂
F SPANF SPAN
SETSET
SCANSCAN
∂ F  SpanSpan: ±±10kHz10kHz
ProgrammedProgrammed P1:P1:0.500.00MHz0.500.00MHz
scanscan edgesedges P2:P2: 29.999.99MHz29.999.99MHz
■
∂∂
F scan operation
q Push [EXIT] one or more times to close a multi-
function screen, if necessary.
w Select VFO mode or a memory channel.
e Select the desired operating mode.
•The operating mode can also be changed while scan-
ning.
r Push [(F-4)SCAN] to select the scan screen.
t Set [RF/SQL] open or closed.
•See previous page for scan condition.
•If the [RF/SQL] control function is set as “AUTO,” the
squelch is always open in SSB, CW and RTTY modes.
See pgs. 3, 68 for details.
y Set the ∂F span by pushing [(F-4)∂F SPAN].
•±5 kHz, ±10 kHz, ±20 kHz, ±50 kHz, ±100 kHz, ±500
kHz and ±1000 kHz are selectable.
u Set center frequency of the ∂F span.
i Push [(F-2)∂F] to start the ∂F scan.
•Decimal points blink while scanning.
o When the scan detects a signal, the scan stops,
pauses or ignores it depending on the resume set-
ting and the squelch condition.
!0 To cancel the scan, push [(F-2)∂F].
ANTANT
1
METERMETER
PoPo
P.AMPP.AMP
1
ATTATT
OFFOFF
VOXVOX
OFFOFF
COMPCOMP
OFFOFF
WIDEWIDE
SFTSFT
0
FIL2FIL2
USBUSB
qw:pp
AGCAGC
MIDMID
TXTX
VFOVFO
USBUSB
USBUSB
USBUSB
FIL2FIL2
qr≥qot≥pp
qr≥wpt≥pp
14.100.0014.100.00
14.100.0014.100.00
1
1
VFOVFO
BWBW
2.4k2.4k
PROGPROG
∂
F FINEFINE
∂
F SPANF SPAN
SETSET
SCANSCAN
∂ F  SCANSCAN
∂ F  CenterCenter:  14.195.00MHz14.195.00MHz
∂ F  SpanSpan: ±±10kHz10kHz
ProgrammedProgrammed P1:P1:0.500.00MHz0.500.00MHz
scanscan edgesedges P2:P2: 29.999.99MHz29.999.99MHz
ANTANT
1
METERMETER
PoPo
P.AMPP.AMP
1
ATTATT
OFFOFF
VOXVOX
OFFOFF
COMPCOMP
OFFOFF
WIDEWIDE
SFTSFT
0
FIL2FIL2
USBUSB
qw:pp
AGCAGC
MIDMID
TXTX
VFOVFO
USBUSB
USBUSB
USBUSB
FIL2FIL2
qr≥qot≥pp
qr≥wpt≥pp
14.100.0014.100.00
14.100.0014.100.00
1
1
VFOVFO
BWBW
2.4k2.4k
PROGPROG
∂
F FINEFINE
∂
F SPANF SPAN
SETSET
SCANSCAN
∂ F  SpanSpan: ±±10kHz10kHz
ProgrammedProgrammed P1:P1:0.500.00MHz0.500.00MHz
scanscan edgesedges P2:P2: 29.999.99MHz29.999.99MHz