Icom IC-756PRO - Select Memory Scan Operation; Setting Select Memory Channels

59
7
SCANS
■ Select memory scan operation
q Push [EXIT] one or more times to close a multi-
function screen, if necessary.
w Select memory mode.
e Select the desired operating mode.
•The operating mode can also be changed while scan-
ning.
r Push [(F-4)SCAN] to select the scan screen.
t Set [RF/SQL] open or closed.
•See p. 56 for scan condition.
•If the [RF/SQL] control function is set as “AUTO,” the
squelch is always open in SSB, CW and RTTY modes.
See pgs. 3, 68 for details.
y Push [(F-1)MEMO] to start the memory scan.
•Decimal points blink while scanning.
u Push [(F-3)SELECT] to start select memory scan;
push [(F-3)SELECT] again to return to memory
scan, if desired.
i When the scan detects a signal, the scan stops,
pauses or ignores it depending on the resume set-
ting and the squelch condition.
o To cancel the scan, push [(F-1)MEMO].
2 or more memory channels must be designated
as select memory channels for select memory
scan to start.
ANTANT
1
METERMETER
PoPo
P.AMPP.AMP
1
ATTATT
OFFOFF
VOXVOX
OFFOFF
COMPCOMP
OFFOFF
WIDEWIDE
SFTSFT
0
FIL2FIL2
USBUSB
qw:pp
AGCAGC
MIDMID
TXTX
VFOVFO
USBUSB
USBUSB
USBUSB
FIL2FIL2
qr≥qot≥pp
qr≥wpt≥pp
14.100.0014.100.00
14.100.0014.100.00
1
VFOVFO
BWBW
2.4k2.4k
MEMOMEMO
∂
F SELECTSELECT
∂
F SPANF SPAN
SETSET
SCANSCAN
1212ß
SELECT MEMORY SCANSELECT MEMORY SCAN
∂ F  SpanSpan: ±±10kHz10kHz
ProgrammedProgrammed P1:P1:0.500.00MHz0.500.00MHz
scanscan edgesedges P2:P2: 29.999.99MHz29.999.99MHz
ANTANT
1
METERMETER
PoPo
P.AMPP.AMP
1
ATTATT
OFFOFF
VOXVOX
OFFOFF
COMPCOMP
OFFOFF
WIDEWIDE
SFTSFT
0
FIL2FIL2
USBUSB
qw:pp
AGCAGC
MIDMID
TXTX
VFOVFO
USBUSB
USBUSB
USBUSB
FIL2FIL2
qr≥qot≥pp
qr≥wpt≥pp
14.100.0014.100.00
14.100.0014.100.00
1
VFOVFO
12 12
BWBW
2.4k2.4k
MEMOMEMO
∂
F SELECTSELECT
∂
F SPANF SPAN
SETSET
SCANSCAN
∂ F  SpanSpan: ±±10kHz10kHz
ProgrammedProgrammed P1:P1:0.500.00MHz0.500.00MHz
scanscan edgesedges P2:P2: 29.999.99MHz29.999.99MHz
■ Setting select memory channels
q Push [EXIT] one or more times to close a multi-
function screen, if necessary.
w Select memory mode.
e Push [(F-4)SCAN] to select the scan screen.
r Select the desired memory channel to set as se-
lect memory channel.
t Push [(F-3)SELECT] to set the memory channel
as a select memory or not.
y Repeat steps r to t to program another memory
channel as a select memory channel, if desired.
u Push [EXIT] to exit the scan screen.
Select memory channels can also be set in the
memory channel screen. (p. 51)
1212ß
ANTANT
1
METERMETER
PoPo
P.AMPP.AMP
1
ATTATT
OFFOFF
VOXVOX
OFFOFF
COMPCOMP
OFFOFF
WIDEWIDE
SFTSFT
0
FIL2FIL2
USBUSB
qw:pp
AGCAGC
MIDMID
TXTX
VFOVFO
USBUSB
USBUSB
USBUSB
FIL2FIL2
qr≥qot≥pp
qr≥wpt≥pp
14.100.0014.100.00
14.100.0014.100.00
1
VFOVFO
BWBW
2.4k2.4k
MEMOMEMO
∂
F SELECTSELECT
∂
F SPANF SPAN
SETSET
SCANSCAN
“ß” appears for select memory channels.
∂ F  SpanSpan: ±±10kHz10kHz
ProgrammedProgrammed P1:P1:0.500.00MHz0.500.00MHz
scanscan edgesedges P2:P2: 29.999.99MHz29.999.99MHz
ANTANT
1
METERMETER
PoPo
P.AMPP.AMP
1
ATTATT
OFFOFF
VOXVOX
OFFOFF
COMPCOMP
OFFOFF
WIDEWIDE
SFTSFT
0
FIL2FIL2
USBUSB
qw:pp
AGCAGC
MIDMID
TXTX
VFOVFO
USBUSB
USBUSB
USBUSB
FIL2FIL2
qr≥qot≥pp
qr≥wpt≥pp
14.100.0014.100.00
14.100.0014.100.00
1
VFOVFO
12 12
BWBW
2.4k2.4k
MEMOMEMO
∂
F SELECTSELECT
∂
F SPANF SPAN
SETSET
SCANSCAN
∂ F  SpanSpan: ±±10kHz10kHz
ProgrammedProgrammed P1:P1:0.500.00MHz0.500.00MHz
scanscan edgesedges P2:P2: 29.999.99MHz29.999.99MHz