Icom IC-756PRO - Fine Programmed Scan;Fine ∂F Scan; Memory Scan Operation

58
7
SCANS
■ Fine programmed scan/fine ∂F scan
Fine scan functions as programmed or ∂F scan, but
scan speed decreases when the squelch opens but
does not stop. The scanning tuning step shifts from
50 Hz to 10 Hz while the squelch opens.
q Push [EXIT] one or more times to close a multi-
function screen, if necessary.
w Push [(F-4)SCAN] to select the scan screen.
e Set for programmed scan or ∂F scan as described
on previous page.
r Push [(F-1)PROG] or [(F-2)∂F] to start a scan.
•Decimal points blink while scanning.
t Push [(F-3)FINE] to start a fine scan.
•“FINE PROGRAM SCAN” or “FINE ∂F SCAN” appears.
y When the scan detects a signal, the scan speed
decreases but does not stop.
u Push [(F-1)PROG] or [(F-2)∂F] to stop the scan;
push [(F-3)FINE] to cancel the fine scan.
ANTANT
1
METERMETER
PoPo
P.AMPP.AMP
1
ATTATT
OFFOFF
VOXVOX
OFFOFF
COMPCOMP
OFFOFF
WIDEWIDE
SFTSFT
0
FIL2FIL2
USBUSB
qw:pp
AGCAGC
MIDMID
TXTX
VFOVFO
USBUSB
USBUSB
USBUSB
FIL2FIL2
qr≥qot≥pp
qr≥wpt≥pp
14.100.0014.100.00
14.100.0014.100.00
1
1
VFOVFO
BWBW
2.4k2.4k
PROGPROG
∂
F FINEFINE
∂
F SPANF SPAN
SETSET
SCANSCAN
FINE PROGRAM SCANFINE PROGRAM SCAN
∂ F  SpanSpan: ±±10kHz10kHz
ProgrammedProgrammed P1:P1:0.500.00MHz0.500.00MHz
scanscan edgesedges P2:P2: 29.999.99MHz29.999.99MHz
ANTANT
1
METERMETER
PoPo
P.AMPP.AMP
1
ATTATT
OFFOFF
VOXVOX
OFFOFF
COMPCOMP
OFFOFF
WIDEWIDE
SFTSFT
0
FIL2FIL2
USBUSB
qw:pp
AGCAGC
MIDMID
TXTX
VFOVFO
USBUSB
USBUSB
USBUSB
FIL2FIL2
qr≥qot≥pp
qr≥wpt≥pp
14.100.0014.100.00
14.100.0014.100.00
1
1
VFOVFO
BWBW
2.4k2.4k
PROGPROG
∂
F FINEFINE
∂
F SPANF SPAN
SETSET
SCANSCAN
PROGRAM SCANPROGRAM SCAN
∂ F  SpanSpan: ±±10kHz10kHz
ProgrammedProgrammed P1:P1:0.500.00MHz0.500.00MHz
scanscan edgesedges P2:P2: 29.999.99MHz29.999.99MHz
■ Memory scan operation
q Push [EXIT] one or more times to close a multi-
function screen, if necessary.
w Select memory mode.
e Select the desired operating mode.
•The operating mode can also be changed while scan-
ning.
r Push [(F-4)SCAN] to select the scan screen.
t Set [RF/SQL] open or closed.
•See p. 56 for scan condition.
•If the [RF/SQL] control function is set as “AUTO,” the
squelch is always open in SSB, CW and RTTY modes.
See pgs. 3, 68 for details.
y Push [(F-1)MEMO] to start the memory scan.
•Decimal points blink while scanning.
u When the scan detects a signal, the scan stops,
pauses or ignores it depending on the resume set-
ting and the squelch condition.
i To cancel the scan, push [(F-1)MEMO].
2 or more memory channels must be programmed
for memory scan to start.
ANTANT
1
METERMETER
PoPo
P.AMPP.AMP
1
ATTATT
OFFOFF
VOXVOX
OFFOFF
COMPCOMP
OFFOFF
WIDEWIDE
SFTSFT
0
FIL2FIL2
USBUSB
qw:pp
AGCAGC
MIDMID
TXTX
VFOVFO
USBUSB
USBUSB
USBUSB
FIL2FIL2
qr≥qot≥pp
qr≥wpt≥pp
14.100.0014.100.00
14.100.0014.100.00
1
VFOVFO
12 12
BWBW
2.4k2.4k
MEMOMEMO
∂
F SELECTSELECT
∂
F SPANF SPAN
SETSET
SCANSCAN
MEMORY SCANMEMORY SCAN
∂ F  SpanSpan: ±±10kHz10kHz
ProgrammedProgrammed P1:P1:0.500.00MHz0.500.00MHz
scanscan edgesedges P2:P2: 29.999.99MHz29.999.99MHz
ANTANT
1
METERMETER
PoPo
P.AMPP.AMP
1
ATTATT
OFFOFF
VOXVOX
OFFOFF
COMPCOMP
OFFOFF
WIDEWIDE
SFTSFT
0
FIL2FIL2
USBUSB
qw:pp
AGCAGC
MIDMID
TXTX
VFOVFO
USBUSB
USBUSB
USBUSB
FIL2FIL2
qr≥qot≥pp
qr≥wpt≥pp
14.100.0014.100.00
14.100.0014.100.00
1
VFOVFO
12 12
BWBW
2.4k2.4k
MEMOMEMO
∂
F SELECTSELECT
∂
F SPANF SPAN
SETSET
SCANSCAN
∂ F  SpanSpan: ±±10kHz10kHz
ProgrammedProgrammed P1:P1:0.500.00MHz0.500.00MHz
scanscan edgesedges P2:P2: 29.999.99MHz29.999.99MHz