Ikegami HDK-73 - Page 98

82
i
Menu Item Initial setting Setting value Description, Remarks
MENU DATA
ALL VF
FOCUS ASSIST
―
ASSIST AREA
75,**(521
75,**(521
$/:$<6212))
6HWVWKH$66,67$5($GLVSOD\
6HOHFW75,**(521LI\RXZLVKWRGLVSOD\
with the trigger of lens operation, etc.
××
―
TRIGGER
FOCUS
FOCUS, FOCUS/
=220/(16975
7ULJJHUWRGLVSOD\$66,67$5($
7KLVVHWWLQJLVXVHGZKHQ75,**(521LV
selected.
××
―
AREA ON/OFF SW
NONE
LENS VTR, EXT
SW, NONE"
6HOHFWVWKHVZLWFKWRWXUQ212))WKH$66,67
$5($
××
―
VF DOT BY DOT
UNLINK LINK, UNLINK
Sets whether a control signal is sent to a VF
KDYLQJD'27%<'27GLVSOD\IXQFWLRQ
××
―
FOR RET
ON ON, OFF
6HWVZKHWKHUWRGLVSOD\WKH$66,67$5($RU
not when switching to the RET signal.
××
―
ASSIST DATA
NO.1 N0.1 to N0.4
6HOHFWVWKH$66,67'$7$FRPSLOHGLQWKH
$66,67'$7$6(77,1*PHQX
××
ASSIST DATA SETTING
NO.1 NO.2 NO.3 NO.4
―
SW ACTION
$/7(51$7( $/7(51$7( $/7(51$7( $/7(51$7(
$/7(51$7(
020(17$5<
If the trigger has been assigned to the LENS
VTR SW, sets whether it is momentary
operation or alternate operation.
○○
―
AREA DISP TIME
1.0S 1.0S 1.0S 1.0S
0.0S to 5.0S
(0.5sec increments)
Sets the time from trigger detection until the
focus assist area is erased.
○○
―
AREA SIZE
15 15 15 100 1 to 100
Sets the focus assist area range.
If set to "100", it is the entire screen domain.
○○
―
AREA LEVEL
60% 60% 60% 100% 25% to 100% 6HWVWKHLPDJHOHYHORIWKH$66,67$5($
○○
―
AREA COLOR
MONO MONO COLOR COLOR
MONO, COLOR,
1(*$
6HWVZKHWKHUWKH$66,67$5($LPDJHVKRXOG
be color, monochrome or negative.
○○
―
AREA MARKER
OFF OFF OFF OFF ON, OFF
Sets whether the assist area frame marker is
displayed or not.
○○
―
EDGE BOOST
LEVEL
55 55 55 55 1 to 100 Sets the boost level of the edge signal.
○○
―
EDGE COLOR
MONO
<(//2: *5((1 <(//2:
0212&<$1
0$*(17$
<(//2:*5((1
RED, BLUE
Sets the color of the edge signal.
○○
STORE DATA
--- --- --- --- N0.1 to N0.4
7KHFRQWHQWVVHWLQWKH$66,67'$7$
6(77,1*PHQXDUHVWRUHGDV$66,67'$7$
Select the numbers you wish to store from No.
1 to No. 4 and write over the present data to
store them.
‐‐
MIC GAIN CONTROL
―
MIC1 STEP
-40dB
G%G%G%
-20dB, -30dB,
-40dB,
-50dB, -60dB
The MIC1 gain is changed step by step.
○×
―
MIC1 FINE
0 -100 to 100
Fine adjustment of the MIC1 gain. The gain
decreases about -8 dB with -100, and increases
DERXWG%ZLWK
○×
―
MIC2 STEP
-40dB
G%G%G%
-20dB, -30dB,
-40dB,
-50dB, -60dB
The MIC2 gain is changed stepwise.
○×
MIC2 FINE
0 -100 to 100
Fine adjustment of the MIC2 gain. The gain
decreases about -8 dB with -100, and increases
DERXWG%ZLWK
○×
RETURN SELECT MODE
―
RET-2/MIC SEL
RET-2 RET-2, MIC
$OORFDWHVDIXQFWLRQWRWKH5(70,&EXWWRQ
on top of handle and on left side of camera.
○×
―
VTR SW SEL
RET-2
RET-2, MIC,
)2&86$667
Sets a function to the VTR SW button on the lens.
,IWKH)2&86$66,67PHQX75,**(5LVVHW
WR/(16975LWEHFRPHV)2&86$667IL[HG
(information display).
○×
RET PRIORITY
127+,1*
127+,1*5(7
RET-2
If a RET-1 or RET-2 image is not displayed in
the viewfinder, sets the output signal to MON
SDI (during RETURN setting).
127+,1* 6HWVWR5(7LPDJHODVWGLVSOD\HG
in VF.
5(7    6HWVWR5(7LPDJH
5(7    6HWVWR5(7LPDJH
○×
FILTER SERVO MODE
SERVO CONT
SERVO 6(5920$18$/
6(592   6HWVWRDXWRPDWLFFRQWURO
0$18$/ 6HWVWRPDQXDOFRQWURO
○×